Trailing-Edge
-
PDP-10 Archives
-
bb-bt99g-bb
-
readme.013
There are no other files named readme.013 in the archive.
1.0 INTRODUCTION
This is the thirteenth Autopatch set. It contains patches for
ALGOL-10-V1-2, ANF10-V23, APL-10-V2, APLSF-10-V2, COBOL-10-V12C,
DECNET-10-UTILITIES-V702, FORTRAN-10-V10, GALAXY-10-V702,
IBMCOM-10-ET-V4, IBMCOM-10-HASP-V1, LINK-10-V5-1, MCB-10-V702,
SORT-10-V4D, TOPS-10-KL-V702, TOPS-10-KS-V702, and UTILITIES-10-V702.
To install Autopatch for the first time, you must first restore the
second save set and follow the instructions found in the Autopatch
Procedures/Reference Manual and the INSTAL.DOC file. Information
specific to each product is recorded in section 5.0 of this document.
2.0 EXCEPTIONS
1. COBOL-10-V12C and SORT-10-V4D are autopatched for the first
time with this tape.
2. The following product(s) are no longer Autopatched because of
new releases: COBOL-10-V12B, FORTRAN-10-V6, FORTRAN-10-V7,
GALAXY-10-V4-1, NFT-10-V1, SORT-10-V4C, TOPS-10-DN6X-V701A,
TOPS-10-KI-V701A, TOPS-10-KL-V701A, TOPS-10-KS-V701A,
TOPS-10-MPE-V701A, TOPS-10-TSK-V701, and UTILITIES-10-V701A.
*NOTE* It is strongly suggested that you DESELECT any of these
products before proceeding with processing any currently
supported products.
3. The following Autopatched product(s) do not have any new edits
delivered with this patch set: APL-10-V2, APLSF-10-V2,
DBMS-10-V5A, MCB-10-V702, MS-10-V10, RMS-10-V1, and
TOPS-10-MPE-V702.
4. (*new*) There are six Patch Command Files on this save-set.
They are APL1B2.MKL, APL1S2.MKL, DBMV5A.MKL, MPE702.SUP, and
RMS1V1.MKL. These products have no patches on this tape.
Without these files, if you were to 'AUTOPATCH' the products
with PEP and SUBmit the patch and build control files the
process would use old patching indirect command files. This
would cause a failure with DBMS and unnecessary processing with
RMS. The 'null' patching indirect command files will avoid
this problem. Any checksum warnings regarding these files may
be ignored.
5. (tape 12) The patches for UTILITIES-10-V702 for tape 11 did not
get applied on tape 11. The utilities involved are BACKUP,
DIRECT, FILCOM, INITIA, PFH and SYSTAT. While the correct
patch files were present, the entries in the Distributed Patch
Directory (DPD) file were labeled incorrectly. All of the
edits have been delivered on tape 12. No special procedures
are required to implement all edits.
6. (tape 11) The Autopatch build for source-patched products will
Page 2
delete source files in PAT: to prevent problems if a build is
re-started. This process may fail if PAT: is defined with
SFDs. Either do not use SFDs when defining PAT: or manually
delete the source files in the SFD before re-starting the
Autopatch build.
7. (tape 11) The TOPS-10-KL and TOPS-10-KS product builds will
fail unless they can find a JOBDAT.REL file in SYS:. In fact,
this file is not used but a lookup does occur.
8. (tape 11) If you are using the new FORTRAN-10 V10 with DBMS you
will need a revised DBCS1F.CMD file from the second save-set on
the Autopatch tape. This file should be copied into the
FORTRAN distribution area. The copy of this file which was
distributed with DBMS V5A must be removed or the FORTRAN build
will fail.
9. (tape 11) A revised copy of TGHA.EXE is contained in the first
save-set on this tape. This copy is required for use of the
new MG20 memory.
10. (tape 10) If you are using DBMS with FORTRAN or COBOL, do not
INSTALL DBMS with PEP until FORTRAN and/or COBOL has been
built. A feature of PEP which was new with tape 9 deletes the
autopatched files from PAT: upon successful installation. The
COBOL and FORTRAN products depend on the necessary DBMS files
being in PAT:.
11. (tape 10) There are new batch control files for
TOPS-10-DCN-V702 and TOPS-10-MPE-V702 in the installation
(second) save-set. They have been modified to 'leave' the
correct support files for the monitor build in PAT: when the
products are autopatched and no edits have been delivered.
These files are restored to PAT: by the product BACKUP command
files.
12. (tape 10) There are three .REL modules for DBMS (FML10, INF10
and MND10) which are null. This causes a %CGV error message at
the end of the batch job and when PEP is checking the results
of the batch job. These messages should be ignored.
13. (tape 9) KS10 systems may have a problem with PFH effectively
hanging. The problem can be avoided by using the /CORE switch
to the SUBMIT command to specify a page limit which is 300
pages or greater.
14. (tape 9) The DECNET-10-UTILITIES-V702 product obsoletes the
NFT-10-V1 Autopatch product. All edits previously delivered to
NFT are included in the new product. DECNET customers who have
previously Autopatched NFT should use the RESTORE NFT-10-V1
command and the DESELECT NFT-10-V1 command to PEP. These
customers should then use the DCN702.CCL file to load the
distribution area.
Customers who are Autopatching DECNET for the first time should
Page 3
use the DCN702.CCL file which also loads monitor modules for
DECNET. All DECNET customers should then install
DECNET-10-UTILITIES for Autopatching.
15. (tape 9) Patch files for four Utilities were improperly
delivered on tape 8. None of the files were referenced in the
Distributed Patch Directory file (PAT108.DPD) and therefore had
no effect via Autopatch. The CREF.C08 and INITIA.C08 files
were, in effect, empty. The DIRECT.C08 file had a bad edit,
and the COMPIL.C08 file had good edits but they were not
applied. You will have problems with Autopatch ONLY if you
applied either the DIRECT or COMPIL edits manually, outside of
the Autopatch process. The COMPIL edits are applied via
Autopatch as a part of tape 9.
16. (tape 9) The ANF10 product is NOT rebuilt by Autopatch. The
Autopatch process will update the supported sources in the DIS:
area. After the INSTALL command has been processed, the
customer may use the sources in DIS: to rebuild the product
with procedures which are appropriate for your site.
17. (tape 9) A new MS1V10.CTL file is provided in the second
save-set. The change was made so that it would not fail even
if used when no patches are provided.
18. (tape 9) There are two new features of PEP and PEPB which are
worthy of note. First, the new PEP will automatically delete
copies of files in PAT: which have been successfully installed
with the INSTALL command.
Second, the definition of ASL: has been changed to be
PAT:,DIS:,INS:. The old definition was
PAT:,DIS:,REL:,UNV:,SYS:. This change was made to obtain
better control over all files used in the build process. We
have delivered what we believe to be a complete set of base
building software on the Autopatch tape. If your procedure has
problems you may have to copy certain files into PAT:, DIS:, or
INS:.
The following files are required for Autopatch use, not put in
place by Autopatch, and may have been previously found in SYS:.
IBMCOM HASP and ET
DDT11.EXE GALCNF.UNV MACDLX.EXE
FORTRAN
BLIS10.EXE BLIS10.ERR
RMS
RMSINI.REL
TOPS-10 KL
Page 4
FKL.MAC HDWKL.MAC TTYKL.MAC NETKL.MAC
TOPS-10 KS
FKS.MAC HDWKS.MAC TTYKS.MAC NETKS.MAC
If these files are currently found in SYS: they must be copied
or moved to PAT:, DIS:, or INS:.
The SORT product currently looks for FTDEFS.UNV amd METUNV.UNV
in ASL:. In fact the SORT build does NOT use these files.
This will be fixed on a future Autopatch tape. Since SYS: is
no longer in the ASL: definition, you may have to copy these
files from SYS:. Users who Autopatch SORT for the first time
and users who have these files in PAT: from a previous COBOL
build will not have this problem.
19. (tape 9) If you Autopatch both COBOL and GALAXY, build Galaxy
before COBOL, but INSTALL COBOL before GALAXY, you will get a
checksum warning and the 'wrong' CHREQV.UNV file in INS:.
The CHREQV.UNV file is not, in fact, needed any longer by
GALAXY. Unless you depend on GALAXY's CHREQV.UNV file being in
INS: for other reasons, this problem should be ignored.
First-time users of Autopatch on GALAXY will not experience the
error.
20. (tape 9) The IBMCOM products have a module named MACROS.P11
which conflicts with a module by the same name with different
contents in the ANF10 product. The IBMCOM MACROS module has
been renamed as MACRO.P11. For users of Autopatch on the
IBMCOM products for the first time, if the IETV04 or IHSV01
.CCL file is used to load the distribution directory then no
action is required by the user. Otherwise, the distributed
MACROS.P11 file must be renamed to be MACRO.P11 or the
MACRO.P11 file on the Autopatch tape must be put in DIS:. The
UTILTY.UPD file will update the Patch Database file.
Also note that IBMCOM products use some galaxy supported files.
Be sure that the GALAXY product has been Autopatched through
the control file phase before Autopatching IBMCOM products.
21. (tape 8) The monitor, CUSPS and GALAXY components supported by
this tape are all based on the products as delivered with the
TOPS-10 V7.02 release. It is suggested that all DIS:
distribution directories for the previous versions be cleared
or moved elsewhere before installing the new versions for
Autopatching. The supplied updates will not apply to the
V7.01A components including GALAXY-10-V4-1. LINK and RMS
remain unchanged from the V7.01A release to the V7.02 release
and, therefore, do NOT need to be re-installed.
22. (tape 8) The CCL files in the second save set of this tape are
Page 5
designed to aid the process of loading the DIS: directories
from the product distribution tapes. The CSP702.CCL permits
'one pass' of the CUSP to load all files needed for
UTILITIES-10-V702, GALAXY-10-V702, and TOPS-10-K?-V702. Use of
the GAL702.CCL or UTL702.CCL files is appropriate only if you
do not use the CSP702.CCL file. The monitor products also
require files from the CUSSUP tape. The CSC702.CCL file will
accomplish this task. The DCN702.CCL file will load monitor
modules and the DECNET utility files.
23. (tape 8) Labelled tapes written through the services of PULSAR
may not be compatible with the previous version of PULSAR. See
the GAL702.B08 file.
24. (tape 8) The TOPS-10-MPE-V702 and TOPS-10-DCN-V702 products do
not require a build procedure. There are no 'output' files,
only updated source files. The LOG files for these products
will show messages relating to zero checksums and the inability
to get version numbers. These messages may be ignored.
25. (tape 8) The COBOL, LINK and SORT LOG files will show a
warnings about three obsolete references (.SGNAM, .SGPPN and
.SGDEV). These will be changed at a later time. The warnings
may be ignored.
26. (tape 7) Changes have been made to the PEP utility. It is
MANDATORY that PEP.EXE and PEPB.EXE be restored to SYS: from
the installation (second) save-set.
Due to a limited amount of space in some of PEP's internal
tables, we are now declaring some products to be "obsolete".
These products will be removed from PEP's internal tables. For
the most part this process is transparent to you, unless the
obsolete product has previously been SELECTed. Suppose
FORTRAN-10-V6 is one of your SELECTed products. In that case,
the following message would be displayed the first time you run
the new PEP:
[FORTRAN-10-V6 is now obsolete.
Edits are no longer being delivered.
You should DESELECT this product.]
This message will only appear ONCE PER SELECTED OBSOLETE
PRODUCT. Use the DESELECT command to purge the obsolete
product from your database.
NOTE
The PEP101.PDF file is NOT compatible with earlier
versions of PEP.
There is now a short version of the INFORMATION command called
Page 6
STATUS. It displays the status information and logical name
definitions, but does not list any files or their checksums.
For example, you might see the following:
PEP>status LINK-10-V5-1
LINK-10-V5-1 is ready to be SETUP for patch and rebuild
Patches retrieved through patch tape 7
Logical names:
PAT: (autopatching directory) defined as DSKP:[7,6]
DIS: (distribution directory) defined as DSKP:[7,6,LINK]
BAK: (backup directory) defined as DSKP:[7,6,BACKUP]
INS: (installation directory) defined as SYS:
ASL: (autopatch search list) defined as PAT:,DIS:,SYS:
27. (tape 7) Edit 612 to DBMS-10-V5A eliminates the need for the
DBSINF.REL module which was introduced on Autopatch tape 5.
Users who have Autopatched DBMS previously are urged to be sure
that the new version of the DBINF1.CMD file is restored from
the patch set 7 save set on this tape. Use of the DBMV5A.Ann
file will accomplish this task.
28. (tape 7) The second chapter of the TOPS-10/TOPS-20 Autopatch
Procedures/Reference Manual suggests a quota of 20,000 blocks
for the [7,6] PPN on page 2-2. Because of additional product
support, it is now suggested that you use a figure of 140000.
29. (tape 6) The patch directory files (.DPD) have been
re-formatted; the same number of edits, but less 'patches',
are described. Also, intermediate checkpointing has been
suppressed during the execution of the PEP 'AUTOPATCH' command.
Checkpoint processing time has been SIGNIFICANTLY reduced.
These changes will improve PEP performance, but will cause
minor variations from the examples provided on pages 2-7, 2-17
and 3-8 of the Autopatch Procedures/Reference Manual.
30. (tape 6) Users of FORTRAN with DBMS MUST create a file - read
the INSTAL.DOC file.
If you have previously SELECTed DBMS for Autopatch and
indicated that FORTRAN was being used than you may want to 're
do' DBMS. FORTRAN V6 is no longer supported by Autopatch.
With FORTRAN V7 and later the FORLIB.REL file is not modified
for DBMS and the DBMSF.EXE file is autopatched by FORTRAN.
The suggested procedure is to use the DBMV5A.Ann file to
restore all files for DBMS from this tape and issue the
DESELECT and SELECT commands for DBMS-10-V5A to PEP before
Autopatching DBMS. Otherwise, the DBMS Autopatch process will
'install' copies of FORLIB.REL and DBMSF.EXE which is also done
by the FORTRAN Autopatch process.
31. (tape 6) There are three warning messages seen during the
Page 7
patching of REL libraries of the DBMS product. Newer edits are
trying to remove edits which were suppressed. This condition
is non-fatal and has no impact on the success of DBMS updating.
Ignore the messages.
32. (tape 6) BATCH time limits for FORTRAN and COBOL should be high
to ensure that the product build BATCH jobs do not abort due to
CPU time overrun. Use a figure of 5 hours to cover all
possibilities.
33. (tape 6) Some products can optionally use other products. This
means that one product may have to be patched and rebuilt
before another product. For example, COBOL can optionally use
the DBMS product. The COBOL Autopatch process requires that
DBMS and SORT be updated before COBOL. In order to apply all
patches correctly you must SUBMIT the Patch and Build Control
file for SORT and DBMS before the COBOL Control file. The MPE
and DCN options to the TOPS-10 Monitor must be Autopatched
before the Control file to build the monitor is submitted.
34. (tape 5) Before selecting the ALGOL product for Autopatching be
sure to read the note in the INSTAL.DOC file regarding a
required rename of the OTS.
35. (tape 4) When PEP is run, the default directory must be PAT:.
36. (tape 4) It is advised that all desired products be SELECTed
for Autopatching before entering the AUTOPATCH or RETRIEVE
command for the first time. The patch retrieval process is NOT
product specific. This process can be invoked with the
RETRIEVE command or the AUTOPATCH command. PEP will then read
the entire patch directory file (.DPD) and update the patch
database file (.PDB) for all SELECTed products. If the
AUTOPATCH command is entered for a product which was SELECTed
at the time of a prior retrieval process, a statement will be
made indicating that all patches have already been retrieved.
3.0 RELATED DOCUMENTS
TOPS-10/TOPS-20 Autopatch Procedures/Reference Manual (AA-H729A-TK)
INSTAL.DOC (in Installation Save Set on this tape)
4.0 FILE INDEX
Page 8
Patch Set 013
File Description
README.013 Patch Set 013 Master Documentation File
TAP013.DIR Directory with Checksums of Patch Set 013
PAT113.DPD Patch Directory File for Patch Set 013
APL1B2.MKL Null Patch Command Files
APL1S2.MKL
DBMV5A.MKL
MPE702.SUP
RMS1V1.MKL
APEDIT.RPT Autopatch Edit Report
UTILTY.UPD Utility checksum and version update file
Edit Description Files
CBL12C.D13 COBOL-10-V12C Edit Description File
FTN10.D13 FORTRAN-10-V10 Edit Description File
GAL702.D13 GALAXY-10-V702 Edit Description File
IETV04.D13 IBMCOM-10-ET-V4 Edit Description File
IHSV01.D13 IBMCOM-10-HASP-V1 Edit Description File
SRTV4D.D13 SORT-10-V4D Edit Description File
T1L702.D13 TOPS-10-KL-V702 Edit Description File
T1S702.D13 TOPS-10-KS-V702 Edit Description File
UTL702.D13 UTILITIES-10-V702 Edit Description File
Patch Files
CBLIO.C13 CBLIO .MAC Patch File COBOL-10-V12C
CLEANC.C13 CLEANC.MAC
CMNGEN.C13 CMNGEN.MAC
COBOLC.C13 COBOLC.MAC
COBST.C13 COBST .MAC
COBVER.C13 COBVER.MAC
CPYLIB.C13 CPYLIB.MAC
CTREE.C13 CTREE .MAC
GETITM.C13 GETITM.MAC
IMPURE.C13 IMPURE.MAC
ISAM.C13 ISAM .MAC
LIBARY.C13 LIBARY.MAC
MOVGEN.C13 MOVGEN.MAC
MSCGEN.C13 MSCGEN.MAC
PSCAN.C13 PSCAN .MAC
SETRET.C13 SETRET.MAC
SRTGEN.C13 SRTGEN.MAC
TABLES.C13 TABLES.MAC
XPAND.C13 XPAND .MAC
Page 9
ACT1.C13 ACT1 .BLI Patch File FORTRAN-10-V10
ARRXPN.C13 ARRXPN.BLI
CGDO.C13 CGDO .BLI
COMSUB.C13 COMSUB.BLI
DEFPT.C13 DEFPT .BLI
EXPRES.C13 EXPRES.BLI
FORDDT.C13 FORDDT.MAC
FORFMT.C13 FORFMT.MAC
FORHST.C13 FORHST.MAC
FORMSG.C13 FORMSG.MAC
FOROPN.C13 FOROPN.MAC
FORPRM.C13 FORPRM.MAC
FORSRT.C13 FORSRT.MAC
LEXICA.C13 LEXICA.BLI
MTHDBL.C13 MTHDBL.MAC
MTHGDB.C13 MTHGDB.MAC
MTHHST.C13 MTHHST.MAC
OUTMOD.C13 OUTMOD.BLI
REGAL2.C13 REGAL2.BLI
REVHST.C13 REVHST.MAC
STA0.C13 STA0 .BLI
STA1.C13 STA1 .BLI
STA3.C13 STA3 .BLI
DORTB.X13 DORTB .EXE Patch File FORTRAN-REP-V10
DORTC.X13 DORTC .EXE
DORTD.X13 DORTD .EXE
DORTE.X13 DORTE .EXE
DORTF.X13 DORTF .EXE
DORTG.X13 DORTG .EXE
DORTRA.X13 DORTRA.EXE
FORDDT.X13 FORDDT.REL
FORLIB.X13 FORLIB.REL
FORO10.X13 FORO10.EXE
FORTB.X13 FORTB .EXE
FORTC.X13 FORTC .EXE
FORTD.X13 FORTD .EXE
FORTE.X13 FORTE .EXE
FORTF.X13 FORTF .EXE
FORTG.X13 FORTG .EXE
FORTRA.X13 FORTRA.EXE
SINGLE.X13 SINGLE.EXE
PLRLBP.C13 PLRLBP.MAC Patch File GALAXY-10-V702
QSRMDA.C13 QSRMDA.MAC
QSRQUE.C13 QSRQUE.MAC
QSRT10.C13 QSRT10.MAC
D60SPD.C13 D60SPD.MAC Patch File IBMCOM-10-ET-V4/
HBSC.C13 HBSC .P11 IBMCOM-10-HASP-V1
IBMPAT.C13 IBMPAT.MAC
IBMSPL.C13 IBMSPL.MAC
STGMAN.C13 STGMAN.MAC
XL3780.C13 XL3780.MAC
Page 10
SRTPRM.C13 SRTPRM.MAC Patch File SORT-10-V4D
SRTSCN.C13 SRTSCN.MAC
CLOCK1.C13 CLOCK1.MAC Patch File TOPS-10-K?-V702
COMMON.C13 COMMON.MAC
DLPSER.C13 DLPSER.MAC KL
FILIO.C13 FILIO .MAC
FILUUO.C13 FILUUO.MAC
IPCSER.C13 IPCSER.MAC
LP2SER.C13 LP2SER.MAC KS
LPTSER.C13 LPTSER.MAC KL
PTYSER.C13 PTYSER.MAC
S.C13 S .MAC
SCNSER.C13 SCNSER.MAC
TAPUUO.C13 TAPUUO.MAC
VMSER.C13 VMSER .MAC
BACKUP.C13 BACKUP.MAC Patch File UTILITIES-10-V702
INITIA.C13 INITIA.MAC
LOGIN.C13 LOGIN .MAC
SYSTAT.C13 SYSTAT.MAC
Base Building Software
ACTSYM.UNV MACRO.EXE
COMPIL.EXE MACSYM.UNV
CREF.EXE MACTEN.UNV
D60JSY.MAC MAKLIB.EXE
D60JSY.REL NCPTAB.REL
D60UNV.MAC ORNMAC.UNV
D60UNV.UNV OVRLAY.REL
DIRECT.EXE PIP.EXE
EDDT.REL QSRMAC.UNV
FORDBM.REL SCAN.REL
GLOB.EXE SCNMAC.UNV
GLXLIB.REL TECO.EXE
GLXMAC.UNV UFDPRM.UNV
HELPER.REL UFDSET.REL
JOBDAT.REL UUOSYM.UNV
JOBDAT.UNV WILD.REL
LINK.EXE
LNK999.EXE
LNKERR.EXE
LNKLOD.EXE
LNKMAP.EXE
LNKOV1.EXE
LNKOV2.EXE
LNKSCN.EXE
LNKXIT.EXE
Page 11
Patch BACKUP Command Files
CBL12C.P13 Restores files from Patch Set #013 for COBOL-10-V12C
FTN10.P13 Restores files from Patch Set #013 for FORTRAN-10-V10
FTN10R.P13 Restores files from Patch Set #013 for FORTRAN-REP-V10
GAL702.P13 Restores files from Patch Set #013 for GALAXY-10-V702
IETV04.P13 Restores files from Patch Set #013 for IBMCOM-10-ET-V4
IHSV01.P13 Restores files from Patch Set #013 for IBMCOM-10-HASP-V1
LNKV51.P13 Restores files from Patch Set #013 for LINK-10-V5-1
SRTV4D.P13 Restores files from Patch Set #013 for SORT-10-V4D
T1L702.P13 Restores files from Patch Set #013 for TOPS-10-KL-V702
T1S702.P13 Restores files from Patch Set #013 for TOPS-10-KS-V702
UTL702.P13 Restores files from Patch Set #013 for UTILITIES-10-V702
Patch BACKUP Command Files
ALG10B.A13 Restores files from ALL Patch Sets for ALGOL-10-V10B
ANFV23.A13 Restores files from ALL Patch Sets for ANF10-V23
APL1B2.A13 Restores files from ALL Patch Sets for APL-10-V2
APL1S2.A13 Restores files from ALL Patch Sets for APLSF-10-V2
CBL12C.A13 Restores files from ALL Patch Sets for COBOL-10-V12C
DBMV5A.A13 Restores files from ALL Patch Sets for DBMS-10-V5A
DCN702.A13 Restores files from ALL Patch Sets for TOPS-10-DCN-V702
DNU702.A13 Restores files from ALL Patch Sets for DECNET-10-UTILITIES-V702
FTN10.A13 Restores files from ALL Patch Sets for FORTRAN-10-V10
FTN10R.A13 Restores files from ALL Patch Sets for FORTRAN-REP-V10
GAL702.A13 Restores files from ALL Patch Sets for GALAXY-10-V702
IETV04.A13 Restores files from ALL Patch Sets for IBMCOM-10-ET-V4
IHSV01.A13 Restores files from ALL Patch Sets for IBMCOM-10-HASP-V1
LNKV51.A13 Restores files from ALL Patch Sets for LINK-10-V5-1
MCB702.A13 Restores files from ALL Patch Sets for MCB-10-V702
MPE702.A13 Restores files from ALL Patch Sets for TOPS-10-MPE-V702
MS1V10.A13 Restores files from ALL Patch Sets for MS-10-V10
RMS1V1.A13 Restores files from ALL Patch Sets for RMS-10-V1
SRTV4D.A13 Restores files from ALL Patch Sets for SORT-10-V4D
T1L702.A13 Restores files from ALL Patch Sets for TOPS-10-KL-V702
T1S702.A13 Restores files from ALL Patch Sets for TOPS-10-KS-V702
UTL702.A13 Restores files from ALL Patch Sets for UTILITIES-10-V702
5.0 PRODUCT DOCUMENTATION
Page 12
ALGOL-10-V10B Product Information PRODUCT CODE:
Patch Set 013 ALG10B
This patch set does not provide any edits for ALGOL-10-V10B.
If you are patching the product for the first time, you must define a
distribution area and obtain some files from the ALGOL-10-V10B
distribution tape. This process is described in the INSTAL.DOC file in
the second save set on this tape and in the Autopatch
Procedures/Reference Manual. The ALG10B.CCL Distribution BACKUP Command
file found in the Installation Save Set may be used for this purpose.
If using Autopatch for the first time on this product you may use the
ALG10B.A13 Patch BACKUP Command file to restore files from all Patch
Sets.
Page 13
ANF10-V23 Product Information PRODUCT CODE:
Patch Set 013 ANFV23
This patch set does not provide any edits for ANF10-V23.
If you are patching the product for the first time, you must define a
distribution area and obtain some files from the TOPS-10 distribution
tape. This process is described in the INSTAL.DOC file in the second
save set on this tape and in the Autopatch Procedures/Reference Manual.
The ANFV23.CCL, T1L702.CCL or T1S702.CCL Distribution BACKUP Command
file found in the Installation Save Set may be used for this purpose.
If using Autopatch for the first time on this product you may use the
ANFV23.A13 Patch BACKUP Command file to restore files from all Patch
Sets.
Page 14
APL-10-V2 Product Information PRODUCT CODE:
Patch Set 013 APL1B2
This patch set does not provide any edits for APL-10-V2.
If you are patching the product for the first time, you must define a
distribution area and obtain some files from the APL-10-V2 distribution
tape. This process is described in the INSTAL.DOC file in the second
save set on this tape and in the Autopatch Procedures/Reference Manual.
The APL1B2.CCL Distribution BACKUP Command file found in the
Installation Save Set may be used for this purpose. If using Autopatch
for the first time on this product you may use the APL1B2.A13 Patch
BACKUP Command file to restore files from all Patch Sets.
Page 15
APLSF-10-V2 Product Information PRODUCT CODE:
Patch Set 013 APL1S2
This patch set does not provide any edits for APLSF-10-V2.
If you are patching the product for the first time, you must define a
distribution area and obtain some files from the APLSF-10-V2
distribution tape. This process is described in the INSTAL.DOC file in
the second save set on this tape and in the Autopatch
Procedures/Reference Manual. The APL1S2.CCL Distribution BACKUP Command
file found in the Installation Save Set may be used for this purpose.
If using Autopatch for the first time on this product you may use the
APL1S2.A13 Patch BACKUP Command file to restore files from all Patch
Sets.
Page 16
COBOL-10-V12C Product Information PRODUCT CODE:
Patch Set 013 CBL12C
This patch set provides the required files to update the COBOL-10-V12C
compiler to edit level 1621, CPYLIB to edit level 10, ISAM to edit level
213, LIBARY to edit level 32, and LIBOL to edit level 1152.
If you are patching the product for the first time, you must define a
distribution area and obtain some files from the COBOL-10-V12C
distribution tape. This process is described in the INSTAL.DOC file in
the second save set on this tape and in the Autopatch
Procedures/Reference Manual. The CBL12C.CCL Distribution BACKUP Command
file found in the Installation Save Set may be used for this purpose.
A description of each edit is contained in the Edit Description file in
Patch Set 013 (CBL12C.D13).
The files required from Patch Set 013 to patch this product are:
PAT113.DPD
and all the Patch Files listed in section 4.0 for this product
You may use the CBL12C.P13 Patch BACKUP Command file to restore files
from Patch Set 013.
If you are using Autopatch for the first time on this product you may
use the CBL12C.A13 Patch BACKUP Command file to restore files from all
Patch Sets.
This product may be Autopatched via EXE/REL replacement. The
CBR12C.CCL, CBR12C.A13 and CBR12C.P13 files are provided for this
purpose. See the INSTAL.DOC file for more details.
Page 17
DBMS-10-V5A Product Information PRODUCT CODE:
Patch Set 013 DBMV5A
This patch set does not provide any edits for DBMS-10-V5A.
If you are patching the product for the first time, you must define a
distribution area and obtain some files from the DBMS-10-V5A
distribution tape. This process is described in the INSTAL.DOC file in
the second save set on this tape and in the Autopatch
Procedures/Reference Manual. The DBMV5A.CCL Distribution BACKUP Command
file found in the Installation Save Set may be used for this purpose.
If you are using Autopatch for the first time on this product you may
use the DBMV5A.A13 Patch BACKUP Command file to restore files from all
Patch Sets.
Page 18
DECNET-10-UTILITIES-V702 Product Information PRODUCT CODE:
Patch Set 013 DNU702
This patch set does not provide any edits for DECNET-10-UTILITIES-V702.
If you are patching the product for the first time, you must define a
distribution area and obtain some files from the TOPS-10 DECNET V7.02
distribution tape. This process is described in the INSTAL.DOC file in
the second save set on this tape and in the Autopatch
Procedures/Reference Manual. The DNU702.CCL Distribution BACKUP Command
file found in the Installation Save Set may be used for this purpose.
If using Autopatch for the first time on this product you may use the
DNU702.A13 Patch BACKUP Command file to restore files from all Patch
Sets.
Page 19
FORTRAN-10-V10 Product Information PRODUCT CODE:
Patch Set 013 FTN10
This patch set provides the required files to update the Fortran
compiler to edit level 2564, the OTS to edit level 4236, and the DDT to
edit level 342.
If you are patching the product for the first time, you must define a
distribution area and obtain some files from the FORTRAN-10-V10
distribution tape. This process is described in the INSTAL.DOC file in
the second save set on this tape and in the Autopatch
Procedures/Reference Manual. The FTN10.CCL Distribution BACKUP Command
file found in the Installation Save Set may be used for this purpose.
A description of each edit is contained in the Edit Description file in
Patch Set 013 (FTN10.D13).
The files required from Patch Set 013 to patch this product are:
PAT113.DPD
and all the Patch Files listed in section 4.0 for this product
You may use the FTN10.P13 Patch BACKUP Command file to restore files
from Patch Set 013.
If you are using Autopatch for the first time on this product you may
use the FTN10.A13 Patch BACKUP Command file to restore files from all
Patch Sets.
This product may be Autopatched via EXE/REL replacement. The
FTN10R.CCL, FTN10R.A13 and FTN10R.P13 files are provided for this
purpose. See the INSTAL.DOC file for more details.
Page 20
GALAXY-10-V702 Product Information PRODUCT CODE:
Patch Set 013 GAL702
This patch set provides the required files to update PULSAR to edit
level 452, and QUASAR to edit level 1240.
If you are patching the product for the first time, you must define a
distribution area and obtain some files from the TOPS-10 V702 CUSP
distribution tape. This process is described in the INSTAL.DOC file in
the second save set on this tape and in the Autopatch
Procedures/Reference Manual. The GAL702.CCL or CSP702.CCL Distribution
BACKUP Command file found in the Installation Save Set may be used for
this purpose.
A description of each edit is contained in the Edit Description file in
Patch Set 013 (GAL702.D13).
The files required from Patch Set 013 to patch this product are:
PAT113.DPD
and all the Patch Files listed in section 4.0 for this product
You may use the GAL702.P13 Patch BACKUP Command file to restore files
from Patch Set 013.
If you are using Autopatch for the first time on this product you may
use the GAL702.A13 Patch BACKUP Command file to restore files from all
Patch Sets.
Page 21
IBMCOM-10-ET-V4 Product Information PRODUCT CODE:
Patch Set 013 IETV04
This patch set provides the required files to update DN60 to edit level
74.
If you are patching the product for the first time, you must define a
distribution area and obtain some files from the IBMCOM 10 E/T V1
distribution tape. This process is described in the INSTAL.DOC file in
the second save set on this tape and in the Autopatch
Procedures/Reference Manual. The IETV01.CCL Distribution BACKUP Command
file found in the Installation Save Set may be used for this purpose.
A description of each edit is contained in the Edit Description file in
Patch Set 013 (IETV01.D13).
The files required from Patch Set 013 to patch this product are:
PAT113.DPD
and all the Patch Files listed in section 4.0 for this product
You may use the IETV01.P13 Patch BACKUP Command file to restore files
from Patch Set 013.
If you are using Autopatch for the first time on this product you may
use the IETV01.A13 Patch BACKUP Command file to restore files from all
Patch Sets.
Page 22
IBMCOM-10-HASP-V1 Product Information PRODUCT CODE:
Patch Set 013 IHSV01
This patch set provides the required files to update DN60 to edit level
74.
If you are patching the product for the first time, you must define a
distribution area and obtain some files from the IBMCOM 10 HASP V4
distribution tape. This process is described in the INSTAL.DOC file in
the second save set on this tape and in the Autopatch
Procedures/Reference Manual. The IHSV04.CCL Distribution BACKUP Command
file found in the Installation Save Set may be used for this purpose.
A description of each edit is contained in the Edit Description file in
Patch Set 013 (IHSV04.D13).
The files required from Patch Set 013 to patch this product are:
PAT113.DPD
and all the Patch Files listed in section 4.0 for this product
You may use the IHSV04.P13 Patch BACKUP Command file to restore files
from Patch Set 013.
If you are using Autopatch for the first time on this product you may
use the IHSV04.A13 Patch BACKUP Command file to restore files from all
Patch Sets.
Page 23
LINK-10-V5-1 Product Information PRODUCT CODE:
Patch Set 013 LNKV51
This patch set does not provide any edits for LINK-10-V5-1.
If you are patching the product for the first time, you must define a
distribution area and obtain some files from the TOPS-10 V702 CUSP
distribution tape. This process is described in the INSTAL.DOC file in
the second save set on this tape and in the Autopatch
Procedures/Reference Manual. The LNKV51.CCL Distribution BACKUP Command
file found in the Installation Save Set may be used for this purpose.
If using Autopatch for the first time on this product you may use the
LNKV51.A13 Patch BACKUP Command file to restore files from all Patch
Sets.
Page 24
MCB-10-V702 Product Information PRODUCT CODE:
Patch Set 013 MCB702
This patch set does not provide any edits for MCB-10-V702
If you are patching the product for the first time, you must define a
distribution area and obtain some files from the DECNET 10 V7.02
distribution tape. This process is described in the INSTAL.DOC file in
the second save set on this tape and in the Autopatch
Procedures/Reference Manual. The MCB702.CCL Distribution BACKUP Command
file found in the Installation Save Set may be used for this purpose.
If you are using Autopatch for the first time on this product you may
use the MCB702.A13 Patch BACKUP Command file to restore files from all
Patch Sets.
Page 25
MS-10-V10 Product Information PRODUCT CODE:
Patch Set 013 MS1V10
This patch set does not provide any edits for MS-10-V10.
If you are patching the product for the first time, you must define a
distribution area and obtain some files from the MS-10-V10 distribution
tape. This process is described in the INSTAL.DOC file in the second
save set on this tape and in the Autopatch Procedures/Reference Manual.
The MS1V10.CCL Distribution BACKUP Command file found in the
Installation Save Set may be used for this purpose.
If you are using Autopatch for the first time on this product you may
use the MS1V10.A13 Patch BACKUP Command file to restore files from all
Patch Sets.
Page 26
RMS-10-V1 Product Information PRODUCT CODE:
Patch Set 013 RMS1V1
This patch set does not provide any edits for RMS-10-V1.
If you are patching the product for the first time, you must define a
distribution area and obtain some files from the TOPS-10 V7.02 CUSP
distribution tape. This process is described in the INSTAL.DOC file in
the second save set on this tape and in the Autopatch
Procedures/Reference Manual. The RMS1V1.CCL Distribution BACKUP Command
file found in the Installation Save Set may be used for this purpose.
If you are using Autopatch for the first time on this product you may
use the RMS1V1.A13 Patch BACKUP Command file to restore files from all
Patch Sets.
Page 27
SORT-10-V4D Product Information PRODUCT CODE:
Patch Set 013 SRTV4D
This patch set provides the required files to update SORT-10-V4D to edit
level 532.
If you are patching the product for the first time, you must define a
distribution area and obtain some files from the SORT-10 V4D or COBOL-10
V12C distribution tape. This process is described in the INSTAL.DOC
file in the second save set on this tape and in the Autopatch
Procedures/Reference Manual. The SRTV4D.CCL or CBL12C.CCL Distribution
BACKUP Command file found in the Installation Save Set may be used for
this purpose.
A description of each edit is contained in the Edit Description file in
Patch Set 013 (SRTV4D.D13).
The files required from Patch Set 013 to patch this product are:
PAT113.DPD
and all the Patch Files listed in section 4.0 for this product
You may use the SRTV4D.P13 Patch BACKUP Command file to restore files
from Patch Set 013. If using Autopatch for the first time on this
product you may use the SRTV4D.A13 Patch BACKUP Command file to restore
files from all Patch Sets.
Page 28
TOPS-10-DCN-V702 Product Information PRODUCT CODE:
Patch Set 013 DCN702
This patch set does not provide any edits for TOPS-10-DCN-V702.
If you are patching the product for the first time, you must define a
distribution area and obtain some files from the TOPS-10 V702 DECNET
distribution tape. This process is described in the INSTAL.DOC file in
the second save set on this tape and in the Autopatch
Procedures/Reference Manual. The DCN702.CCL Distribution BACKUP Command
file found in the Installation Save Set may be used for this purpose.
If you are using Autopatch for the first time on this product you may
use the DCN702.A13 Patch BACKUP Command file to restore files from all
Patch Sets.
Page 29
TOPS-10-KL-V702 Product Information PRODUCT CODE:
Patch Set 013 T1L702
This patch set provides the required files to update the TOPS-10-KL-V702
monitor to edit level 12807 (31007).
If you are patching the product for the first time, you must define a
distribution area and obtain some files from the TOPS-10 V7.02
distribution tape. This process is described in the INSTAL.DOC file in
the second save set on this tape and in the Autopatch
Procedures/Reference Manual. The MON702.CCL, CSC702.CCL and CSP702.CCL
Distribution BACKUP Command files found in the Installation Save Set may
be used for this purpose.
A description of each edit is contained in the Edit Description file in
Patch Set 013 (T1L702.D13).
The files required from Patch Set 013 to patch this product are:
PAT113.DPD
and all the Patch Files listed in section 4.0 for this product
You may use the T1L702.P13 Patch BACKUP Command file to restore files
from Patch Set 013.
If you are using Autopatch for the first time on this product you may
use the T1L702.A13 Patch BACKUP Command file to restore files from all
Patch Sets.
Page 30
TOPS-10-KS-V702 Product Information PRODUCT CODE:
Patch Set 013 T1S702
This patch set provides the required files to update the TOPS-10-KS-V702
monitor to edit level 12807 (31007).
If you are patching the product for the first time, you must define a
distribution area and obtain some files from the TOPS-10 V7.02
distribution tape. This process is described in the INSTAL.DOC file in
the second save set on this tape and in the Autopatch
Procedures/Reference Manual. The MON702.CCL, CSC702.CCL and CSP702.CCL
Distribution BACKUP Command files found in the Installation Save Set may
be used for this purpose.
A description of each edit is contained in the Edit Description file in
Patch Set 013 (T1S702.D13).
The files required from Patch Set 013 to patch this product are:
PAT113.DPD
and all the Patch Files listed in section 4.0 for this product
You may use the T1S702.P13 Patch BACKUP Command file to restore files
from Patch Set 013.
If you are using Autopatch for the first time on this product you may
use the T1S702.A13 Patch BACKUP Command file to restore files from all
Patch Sets.
Page 31
TOPS-10-MPE-V702 Product Information PRODUCT CODE:
Patch Set 013 MPE702
This patch set does not provide any edits for TOPS-10-MPE-V702.
If you are patching the product for the first time, you must define a
distribution area and obtain some files from the TOPS-10 MPE V7.02
distribution tape. This process is described in the INSTAL.DOC file in
the second save set on this tape and in the Autopatch
Procedures/Reference Manual. The MPE702.CCL Distribution BACKUP Command
file found in the Installation Save Set may be used for this purpose.
If you are using Autopatch for the first time on this product you may
use the MPE702.A13 Patch BACKUP Command file to restore files from all
Patch Sets.
Page 32
UTILITIES-10-V702 Product Information PRODUCT CODE:
Patch Set 013 UTL702
This patch set provides the required files to update BACKUP to edit
level 530, INITIA to edit level 254, LOGIN to edit level 1117, and
SYSTAT to edit level 333.
If you are patching the product for the first time, you must define a
distribution area and obtain some files from the TOPS-10 702 CUSP
distribution tape. This process is described in the INSTAL.DOC file in
the second save set on this tape and in the Autopatch
Procedures/Reference Manual. The UTL702.CCL or CSP702.CCL Distribution
BACKUP Command file found in the Installation Save Set may be used for
this purpose.
A description of each edit is contained in the Edit Description file in
Patch Set 013 (UTL702.D13).
The files required from Patch Set 013 to patch this product are:
PAT113.DPD
and all the Patch Files listed in section 4.0 for this product
You may use the UTL702.P13 Patch BACKUP Command file to restore files
from Patch Set 013.
If you are using Autopatch for the first time on this product you may
use the UTL702.A13 Patch BACKUP Command file to restore files from all
Patch Sets.