Trailing-Edge
-
PDP-10 Archives
-
BB-H138A-BM
-
3a-documentation/build.mem
There are 36 other files named build.mem in the archive. Click here to see a list.
+---------------+
! d i g i t a l ! I N T E R O F F I C E M E M O R A N D U M
+---------------+
TO: TOPS20 List A
DATE: 5 JUL 78
FROM: TOPS20 Soft. Eng.
DEPT: DEC20 S. E. Dept.
LOC: MR1-2
FILE: [DOC-SPECS]
BUILD.SPC
SUBJ: TOPS20 Monitor Building Procedures and Information
Fourth Printing, April
1978
COPYRIGHT (C) 1976, 1977, 1978 BY DIGITAL EQUIPMENT
CORPORATION, MAYNARD, MASS.
THIS SOFTWARE IS FURNISHED UNDER A LICENSE AND MAY BE USED AND
COPIED ONLY IN ACCORDANCE WITH THE TERMS OF SUCH LICENSE AND
WITH THE INCLUSION OF THE ABOVE COPYRIGHT NOTICE. THIS
SOFTWARE OR ANY OTHER COPIES THEREOF MAY NOT BE PROVIDED OR
OTHERWISE MADE AVAILABLE TO ANY OTHER PERSON. NO TITLE TO AND
OWNERSHIP OF THE SOFTWARE IS HEREBY TRANSFERRED.
THE INFORMATION IN THIS SOFTWARE IS SUBJECT TO CHANGE WITHOUT
NOTICE AND SHOULD NOT BE CONSTRUED AS A COMMITMENT BY DIGITAL
EQUIPMENT CORPORATION.
DIGITAL ASSUMES NO RESPONSIBILITY FOR THE USE OR RELIABILITY OF
ITS SOFTWARE ON EQUIPMENT WHICH IS NOT SUPPLIED BY DIGITAL.
To: TOPS20 List A Page 2
Subj: TOPS20 Monitor Building Procedures and Info.
1.0 INTRODUCTION
This document provides complete information on configuring and
building the TOPS20 monitor. Multiple configurations are
provided so as to minimize the amount of resident storage used
while supporting all of the available peripheral devices. The
"build" procedure produces a core-image file of the monitor
from the various relocatable files and the one
parameter-dependent source file.
Generally, an installation will be able to run one of the
standard monitor configurations supplied. Section 2 of this
document tells how to select the appropriate monitor
configuration and how to run the build procedure.
Some installations may wish to use a set of configuration
parameters different from those of the standard set. Section 3
describes the function of each parameter and its effect on the
resultant configuration.
Section 4 describes how to add installation-specific terminal
definitions.
2.0 BASIC MONITOR SELECTION AND BUILDING PROCEDURES
Note: This section is intended for anyone who needs to build a
monitor, and it requires a minimum level of familiarity with
the structure or operation of the system. The knowledge which
is required is:
1. How to login and use basic EXEC commands.
2. How to use the magtape file restore program (DUMPER).
3. How to bring up the system with an existing monitor.
To: TOPS20 List A Page 3
BASIC MONITOR SELECTION AND BUILDING PROCEDURES
2.1 How to Select a Monitor Configuration
There are seven standard monitor configurations. The first
four are intended for general timesharing and batch operation
and differ only in overall size. The fifth is intended for
batch-only operation. The sixth and seventh are 2020 monitors.
A eighth configuration is an ARPA-only monitor. The
configuration names and general descriptions are:
"Small" A typical small configuration for general
timesharing.
"Medium" A typical medium-size configuration for general
timesharing.
"Batch" A configuration for batch-only operation on a
medium to large non-ARPA hardware
configuration.
"Big" The largest standard monitor supported by
Digital.
"2020-small" A typical small configuration for general 2020
timesharing.
"2020-medium" A typical medium-sized configuration for
general 2020 timesharing.
"Large" The largest monitor supported by Digital (ARPA
only).
1. If you intend to do batch-only operation and your
machine has at least 128K core, select the "Batch"
monitor. If you have less than 128K core, the "Batch"
monitor does not provide any advantage over the
appropriate general purpose monitor. The "Batch"
monitor supports 14 jobs, 12 pseudo-terminals (PTY's),
8 terminal lines, 256K core memory, 8 magtape units,
and 2 line printers.
2. If you are not using the "Batch" monitor, select one of
the general purpose monitors based on your hardware
configuration. You will want the smallest monitor
which supports all of the hardware you have and which
handles the number of users you wish to allow. All
monitors support up to 8 disk drives.
To: TOPS20 List A Page 4
BASIC MONITOR SELECTION AND BUILDING PROCEDURES
A. The "Small" monitor will support the following:
40 Users (interactive and batch)
64 Terminal Lines, 40 active
256K Core memory
8 Magtape units (max)
2 Line Printers (max)
2350 Pages of swapping space
20 Network Virtual Terminals (ARPA only)
B. The "Medium" Monitor will support the following:
60 Users (interactive and batch)
64 Terminal Lines, 60 active
256K Core memory
8 Magtape Units (max)
2 Line Printers (max)
3070 Pages of swapping space
30 Network Virtual Terminals (ARPA only)
C. The "Big" monitor will support the following:
100 Users (interactive and batch)
128 Terminal lines, 100 active
512K Core memory
8 Magtape units (max)
2 Line printers (max)
5000 Pages of swapping space
40 Network Virtual Terminals (ARPA only)
D. The "2020-small" monitor will support the
following:
40 Users (interactive and batch)
32 Terminal lines, 20 active
256K memory
8 Magtape units (max)
2 Line printer (max)
3000 Pages of swapping space
E. The "2020-medium" monitor will support the
following:
60 Users (interactive and batch)
32 terminal lines, 32 active
512K memory
8 Magtape units (max1
5000 Pages of swapping space
F. The "large" monitor will support the following:
100 Users (interactive and batch)
To: TOPS20 List A Page 5
BASIC MONITOR SELECTION AND BUILDING PROCEDURES
128 Terminal lines, 100 active
1024K Core memory
8 Magtape units (max)
2 Line printers (max)
5000 Pages of swapping space
40 Network Virtual Terminals
This monitor is only supported on ARPA
installations with the AN20 ARPANET Interface.
It does not matter if the monitor you select supports more of
some devices than you have. The resident core requirements of
each device are quite small, and monitors configured between
the ones above would not show significant performance
improvement.
2.2 How to Build a Standard Monitor Configuration
At this point, you will have selected one of the standard
monitor configurations described above (or have constructed
your own parameter file as described in Section 3). The
following step-by-step procedure produces a monitor configured
according to the parameters in the corresponding parameter
file.
( ) 1. Login and connect to a directory containing a
complete set of monitor files. If the monitor
files have not been loaded onto the disk, load them
from your distribution tape using DUMPER (document
TOPS20.DOC ).
( ) 2. If you are building a standard monitor, copy the
appropriate parameter file to "PARAM0.MAC". If you
are building an ARPA monitor, copy the appropriate
parameter file to "PARAN.MAC". The parameter files
for the various monitors are:
Standard Monitor ARPA Monitor ________ _______ ____ _______
"Small" = PARSML.MAC "Small" = ANPSML.MAC
"Medium" = PARMED.MAC "Medium" = ANPMED.MAC
"Batch" = PARBCH.MAC N/A
"Big" = PARBIG.MAC "Big" = ANPBIG.MAC
N/A N/A
N/A N/A
N/A "Large" = ANPLGE.MAC
For example, if you are building a standard small
monitor,
@COPY PARSML.MAC (TO) PARAM0.MAC.1 !new file!
To: TOPS20 List A Page 6
BASIC MONITOR SELECTION AND BUILDING PROCEDURES
If you are building a medium ARPA monitor,
@COPY ANPMED.MAC (TO) PARAN.MAC.1 !new file!
( ) 3. If you are building a standard (OR 2020) monitor,
copy the appropriate name file to "NAMAM0.MAC". If
you are building an ARPA monitor, copy the
appropriate name file to "NAMAN.MAC". The name
files for the various monitors are:
2020 MONITOR ____ _______
N/A
N/A
N/A
N/A
N/A
"2020-SMALL" = P20SML.MAC
"2020-MEDIUM" = P20MED.MAC
N/A
Standard Monitor ARPA Monitor ________ _______ ____ _______
"Small" = NAMSML.MAC "Small" = ANNSML.MAC
"Medium" = NAMMED.MAC "Medium" = ANNMED.MAC
"Batch" = NAMBCH.MAC N/A
"Big" = NAMBIG.MAC "Big" = ANNBIG.MAC
N/A N/A
N/A N/A
N/A "Large" = ANNLGE.MAC
For example, if you are building a standard small
monitor,
@COPY NAMSML.MAC (TO) NAMAM0.MAC.1 !new file!
If you are building a medium ARPA monitor,
@COPY ANNMED.MAC (TO) NAMAN.MAC.0 !new file!
( ) 4. Submit the appropriate batch file for the type of
monitor you are building: TOPS20.CTL for a
standard monitor, T20-AN.CTL for for an ARPA
monitor, T2020.CTL for 2020.
For example, to build a standard small monitor,
@SUBMIT TOPS20/TAG:SINGLE/TIME:2:0:0
To build a medium ARPA monitor,
@SUBMIT T20-AN/TAG:SINGLE/TIME:2:0:0
To: TOPS20 List A Page 7
BASIC MONITOR SELECTION AND BUILDING PROCEDURES
This will leave the monitor in your directory. The
file name of the monitor file is MONITR.EXE.
If it is desirable to build all of the standard
monitors, then submit the control file with a
/TAG:ALL switch, e.g.,
@SUBMIT TOPS20/TAG:ALL/TIME:2:0:0
( ) 5. If this monitor is to be loaded from magtape, copy
the file to magtape.
COPY MONITR.EXE (TO) MTA0:
The tape density must be 1600 BPI for MTBOOT to
work.
The build procedure is now complete and the new monitor is
ready to be brought up using the normal bootstrap procedures.
3.0 THE MONITOR CONFIGURATION PARAMETERS
Note: This section is intended for anyone needing to build a
monitor configuration different from the standard
configurations. It requires some familiarity with the
operation of the system and utility programs, and some
knowledge of the structure of the monitor. Specifically:
1. Everything required in Section 2.
2. How to use the text editor.
3. How to read assembly language.
4. The meaning of common monitor terms, e.g., "jobs",
"forks", "PTY", etc.
The monitor configuration is determined by a single parameter
file PARAM0.MAC (or PARAN.MAC if building an ARPANET monitor).
This file is the only configuration-dependent file required for
a monitor build. To configure a monitor, you will use the text
editor to produce this parameter file. PARAM0.MAC (or
PARAN.MAC) should contain only those parameters that are
different from the standard values listed in PARAMS.MAC. This
section describes the meaning of each parameter and its effect
on the monitor configuration.
You should read each description, determine the proper value
for your configuration, and note this value on a listing of the
parameter file. You can then edit the parameter file to
To: TOPS20 List A Page 8
THE MONITOR CONFIGURATION PARAMETERS
include these values.
Your edited parameter file should be given the name PARAM0.MAC,
(or PARAN.MAC if building an ARPA monitor).
When the new parameter file has been produced, you may follow
the normal monitor build procedure (Section 2).
The Parameter File___ _________ ____
3.1 NTTPTY
The number of pseudo-terminals. This parameter
determines the number of PTYs available. You will need
1 for PTYCON plus 1 for each PTYCON subjob being run,
plus 1 for each simultaneous batch job being run.
Additional PTYs may be allocated for user use of
PTYCON. The resident storage requirement for a PTY is
exactly the same as for a physical terminal, i.e.,
N = 5*NTTPTY
3.2 NTTNVT
The number of Network Virtual Terminals. These devices
are present only on installations using an ARPA
Monitor, with parameter NETN set to 1. The resident
storage requirement for an NVT is exactly the same as
for a physical terminal, i.e.,
N = 5*NTTNVT
3.3 SSPT
The size of the system pages table. This 2-word table
holds information about every open file and every fork.
Its minimum reasonable value is SSPT = 500 + NJOBS +
3*NFKS. It is also used for holding information about
shared file pages if there is sufficient space. This
allows a shared file page to be referenced without its
owning index block also being brought into core. Hence
it is probably most efficient to set SSPT to the value
shown above plus the average number of shared pages in
use in your system. The resident core requirements are
N = 2*SSPT
To: TOPS20 List A Page 9
THE MONITOR CONFIGURATION PARAMETERS
3.4 MAXCOR
The maximum number of physical core pages. This
parameter determines the size of the four core status
tables. It should be set to at least the maximum
amount of core on your system (i.e., #K/2). The
resident core requirements for this parameter are:
N = 5*MAXCOR
3.5 NDST
The size of the drum status table. This table has one
entry for each page of swapping storage. The swapping
area is used for all active pages whether shared or
private. If the swapping area becomes full, the
monitor will move shared pages back to their home
address, but it cannot move private pages. Hence, this
parameter should be set to at least the maximum number
of private pages expected to be in use at one time.
The resident core requirements are:
N = 1*NDST
Note that at least this much swapping space must have
been allocated on the public file structure (PS:).
The next group of parameters refers to the configuration of
peripheral devices. These parameters take a number which is
the maximum number of units of a particular device. Each
device has a parameter related to the device name, i.e., for
device "xxx", there is a parameter "xxxN". Other symbols in
the monitor are constructed by concatenating the device name
with a specific prefix or postfix.
3.6 FEN
Front End Device service. This parameter defines the
number of FE devices present. The FE devices are
psuedo devices used for general transfering of data to
and from the front-end.
To: TOPS20 List A Page 10
THE MONITOR CONFIGURATION PARAMETERS
3.7 MTAN
Magtape service. This parameter is the number of
magtape units present. A maximum of 8 is presently
supported.
3.8 DTEN
DTE20 service. This parameter denotes the number of
DTE's connected to the KL20.
3.9 LPTN
Lineprinter service. LPTN is the number of physical
lineprinters present. A maximum of 2 is presently
supported. (1 for 2020)
3.10 CDRN
Card Reader Service. This specifies the number of card
readers on the front-end.
3.11 CDPN
Spooled card punch. This specifies the number of
spooled card punch queues that are to be set up by
GALAXY.
3.12 SPLTN
Spooled plotter. This symbol specifies the number of
spooled plotter queues that are allowed.
3.13 SPTPN
Spooled paper tape punch. This symbol specifies the
number of spooled paper tape punch queues that are
allowed.
To: TOPS20 List A Page 11
THE MONITOR CONFIGURATION PARAMETERS
3.14 NETN
ARPANET service. This symbol specifies that the
monitor has support for the AN20 ARPANET Interface
hardware. This parameter must be 0 in the Minimum and
Batch monitors.
3.15 DCN
DECNET SERVICE. THIS SPECIFIES THAT THE MONITOR HAS
SUPPORT FOR DECNET.
The following parameters control specific functions of the
system.
3.16 NFKS
The number of forks. This parameter determines the
size of the scheduler fork tables and hence the maximum
number of forks which can exist at any one time. This
parameter is normally set to 3*NJOBS thus allowing an
average of about 3 forks/job. If your system is known
to have an average distinctly above or below this, this
ratio may be changed. The resident core requirements
are:
N = 13*NFKS
3.17 TMZONE
The time zone. This parameter specifies the local time
zone in which the system is being operated. The
monitor standard time and date format (see JSYS manual)
is GMT. Hence, this parameter gives the number of
hours by which local time lags GMT. This value is
assembled into TIMZON and may be changed at system
startup. Values for USA are:
EST = 5
CST = 6
MST = 7
PST = 8
Daylight saving time is handled automatically; this
parameter should be set based on the standard local
time.
To: TOPS20 List A Page 12
THE MONITOR CONFIGURATION PARAMETERS
3.18 MAXFKS
Maximum fork size. This parameter specifies th