Google
 

Trailing-Edge - PDP-10 Archives - bb-bt99p-bb - instal.doc
There are 31 other files named instal.doc in the archive. Click here to see a list.


     INSTAL.DOC for DECSYSTEM-10



           Installation Information for Autopatch-10/20 V1.2
           -------------------------------------------------



     1.0  INTRODUCTION

     This document describes the procedures necessary  to  set  up  your
     DECSYSTEM-10  for  patching software with Autopatch-10/20 V1.2.  It
     augments the information provided in chapter  2  of  the  Autopatch
     Procedures/Reference  Manual.   This  initialization  operation  is
     required only once.  After it has been completed, you will be  able
     to  apply  the  patches  distributed  periodically in the Autopatch
     Kits.

     In order to set up your system for autopatching, you must create  a
     disk  directory  referred  to  as the autopatching directory.  This
     directory is used to  patch  and  rebuild  the  software.   In  the
     autopatching  directory you must install some of the files supplied
     on this patch tape as described in section 2 of this document.

     In addition, you must also prepare  a  distribution  directory  for
     each  product you intend to autopatch.  This operation is described
     for each of  the  autopatchable  products  in  section  3  of  this
     document.

     For  the  DECSYSTEM-10  the  following   products   are   currently
     autopatchable:
        
            Version 10B of ALGOL-10

            Version 7.04 of ANF10

            Version 2 of APLSF-10

            Version 12C of COBOL-10

            Version 7.04 of CUSTOMER-SUPPORTED-10

            Version 5A of DBMS-10

            Version 7.04 of DECNET-10

            Version 11 of FORTRAN-10

            Version 7.04 of GALAXY-10

            Version 4 of IBMCOM/ET-10

            Version 1 of IBMCOM/HASP-10

                                                                  Page 2


            Version 7.04 of MCB-10

            Version 7.04 of MONITOR-10

            Version 7.04 of MPE-10

            Version 11 of MS-10

            Version 1A of MX-10

            Version 4D of SORT-10

            Version 7.04 of TOPS-10 Utilities
                                                                  Page 3


     Autopatch  V1.2  is  supported  for  applying  only  those  patches
     provided  by  Digital Equipment Corporation as part of an Autopatch
     Kit.  Furthermore, those  patches  are  supported  for  distributed
     (field-image)  software  or  distributed  software  that  has  been
     modified only by autopatching.



     2.0  INSTALLING AUTOPATCH

     If you are not using an  autopatching  structure  named  DSKP:,  we
     recommend  that  you make an entry in your login procedures so that
     DSKP:  is assigned to be the structure you will be using.   If  you
     do  this  and  use the default [7,6] ppn, you will not need to edit
     the BACKUP retrieval command files provided to set-up  the  product
     distribution directories and to process the patch tape.

     The second save set of the patch tape contains  tools  and  control
     files  that  are used in the autopatching operation.  A list of all
     the files in this save set is given in section 4 of this  document.
     Use  the  BACKUP  program  to  restore  from  this  save set to the
     appropriate disk directories those files you need.

     The following files should be installed in  [1,4]  or  one  of  the
     directories belonging to SYS:
        
                PEP.EXE
                PEPB.EXE

     The following file should be installed  in  [2,5]  or  one  of  the
     directories belonging to HLP:
        
                PEP.HLP

     The following files should be installed in the disk  directory  you
     have set up as the autopatching directory:
        
                PEP101.PDF
                UPDATE.EXE

     In addition, a product-specific patch and build control file and  a
     product  description  file  must  be  installed in the autopatching
     directory for each product you intend to  autopatch.   These  files
     are  in  the installation save set of the patch tape.  See the last
     section for a list of these files.

     The installation save set also contains indirect command  files  to
     assist  you  in  setting  up  the product distribution directories.
     These BACKUP CCL files are intended to be run  interactively.   See
     the last section for a list of these files.

     For each product you intend to autopatch, you  should  install  the
     associated  control  files  in  the  autopatching  directory.   For
     example, if you intend to autopatch  the  APLSF-10-V2  product  you
     would install
                                                                  Page 4



                APL1S2.CTL      for APLSF-10 rebuild
                APL1S2.PDF      for Autopatch installation
                APL1S2.CCL      for preparing distribution directory
        
     in the autopatching directory.
                                                                  Page 5


     3.0  AUTOPATCH INSTALLATION OF SPECIFIC PRODUCTS

     3.1  PREPARING FOR AUTOPATCHING ALGOL-10

     Before preparing this product for Autopatching, you should  install
     the  product  on  your  system  as  described  in  the installation
     documentation supplied on the product  distribution  tape.   Unless
     the  product is correctly installed, you will not be able to SELECT
     it for Autopatching.

     The disk directory in which you have installed the executable files
     for  ALGOL-10 is referred to as the product installation directory.
     In most cases  this  will  be  [1,4]  or  one  of  the  directories
     belonging to SYS:.  This directory must contain the files:
        
                ALGOL.EXE
                ALGOTS.EXE
                ALGLIB.REL
                ALGDDT.HLP
                ALGOL.HLP

     *NOTE* The ALGOL distribution does not have a ALGOTS.EXE  file  but
     does  have  a  ALG310.EXE file.  For Autopatching this file must be
     named ALGOTS.EXE in  the  ALGOL  Autopatch  Installation  directory
     (INS:).   Unless  you  COPY or RENAME to create the ALGOTS.EXE file
     the PEP SELECT  process  for  ALGOL-10-V10B  will  fail.   An  edit
     supplied  for  the ALGOL compiler changes generated code to use the
     new generic reference to the OTS.

     The following file is required to build the ALGOL product.  It must
     be  available  either in the patching area (PAT:), the distribution
     area (DIS:), or in the installation area (INS:).

        From the first save-set of the Autopatch tape

        HELPER.REL

     This file will be moved from the Autopatch tape when you use one of
     the BACKUP CCL files described in the README file.

     You will need  to  copy  the  following  files  from  the  ALGOL-10
     distribution  tape  BB-D608D-SB(1600  BPI)  or AP-5069D-SB(800 BPI)
     into  the  disk  directory  you  have  set  up  as   the   ALGOL-10
     distribution directory.
        
        From save set ALGOL-SOURCES
        
        ALGCOD.MAC      ALGCON.MAC      ALGDDT.MAC      ALGDEC.MAC
        ALGEXP.MAC      ALGFOR.MAC      ALGFUN.MAC      ALGLIB.MAC
        ALGMAC.MAC      ALGOTS.MAC      ALGPRM.MAC      ALGSER.MAC
        ALGSTB.MAC      ALGSTM.MAC      ALGSYS.MAC      ALGUTL.MAC


     An indirect  command  file  to  perform  this  operation  has  been
     included  in  the  installation  save set on this patch tape.  This
                                                                  Page 6


     file will restore the appropriate files to DSKP:[7,6,ALG].  If  you
     wish  to use this command file, but are not using DSKP:[7,6,ALG] as
     your distribution directory you will have to edit this command file
     to change the /RESTORE command to correspond to your directory.
        
        To use this command file, issue the following commands:
        
        .R BACKUP
        /TAPE tape:
        /@DSKP:ALG10B.CCL[7,6]
        

     The Patch and Build control file for the re-build of  this  product
     as  well  as the Autopatch product description file are supplied in
     the Installation Save-set on the  Autopatch  tape.   See  the  last
     section  of  this  document  for a list of these files.  There is a
     BACKUP command file provided  in  the  first  Save-set  which  will
     restore  these  files  to  the  proper  directory.   See the README
     documentation file in the first Save-set for more information.
                                                                  Page 7


     3.2  PREPARING FOR AUTOPATCHING ANF10

     You will need to copy the following files from the  TOPS  10  V7.04
     Monitor  distribution  tape BB-X140C-SB into the disk directory you
     have set up as the ANF10 distribution directory.
        
        CHK11.P11       DDT.P11         DNCDDH.P11      DNCDDP.P11
        DNCDDQ.P11      DNCDDS.P11      DNCDMC.P11      DNCDUP.P11
        DNCNFG.P11      DNCOMM.P11      DNCRD.P11       DNCTAB.P11
        DNDBG.P11       DNDCMP.P11      DNDCP4.P11      DNDEMO.P11
        DNDEV.P11       DNDH11.P11      DNDL10.P11      DNDM11.P11
        DNDN11.P11      DNDTE.P11       DNDZ11.P11      DNLBLK.P11
        DNLP20.P11      DNLPT.P11       DNMOP.P11       DNNCL.P11
        DNNSP.P11       DNNSP3.P11      DNPLT.P11       DNPTP.P11
        DNPTR.P11       DNRAM.P11       DNRDA.P11       DNRDE.P11
        DNTRCE.P11      DNTSK.P11       DNTTY.P11       DNVFU.P11
        MACROS.P11      S.P11           TSKTST.P11

     An indirect  command  file  to  perform  this  operation  has  been
     included  in  the  installation  save set on this patch tape.  This
     file will restore the appropriate files to DSKP:[7,6,ANF].  If  you
     wish  to use this command file, but are not using DSKP:[7,6,ANF] as
     your distribution directory you will have to edit this command file
     to change the /RESTORE command to correspond to your directory.
        
        To use this command file, issue the following commands:
        
        .R BACKUP
        /TAPE tape:
        /@DSKP:MON704.CCL[7,6]
        

     The ANF product is NOT rebuilt by Autopatch.  The Autopatch process
     will  update  the  supported  sources in the DIS:  area.  After the
     INSTALL command has  been  processed,  the  customer  may  use  the
     sources  in  DIS:  to rebuild the product with procedures which are
     appropriate to the site.

     The Patch control file for the update of this product  as  well  as
     the   Autopatch  product  description  file  are  supplied  in  the
     Installation Save-set on the Autopatch tape.  See the last  section
     of  this  document  for  a  list of these files.  There is a BACKUP
     command file provided in the  first  Save-set  which  will  restore
     these  files to the proper directory.  See the README documentation
     file in the first Save-set for more information.
                                                                  Page 8


     3.3  PREPARING FOR AUTOPATCHING APL

     Before preparing this product for Autopatching, you should  install
     the  product  on  your  system  as  described  in  the installation
     documentation supplied on the product  distribution  tape.   Unless
     the  product is correctly installed, you will not be able to SELECT
     it for Autopatching.

     The disk directory in which you have installed the executable files
     for  APLSF-10 is referred to as the product installation directory.
     In most cases  this  will  be  [1,4]  or  one  of  the  directories
     belonging to SYS:.  This directory must contain the files:
        
                APLSF.EXE
                GENSF.EXE
                TENTAP.EXE

     You will need  to  copy  the  following  files  from  the  APLSF-10
     distribution  tape  BB-D476E-BB(1600  BPI)  or AP-5065E-BB(800 BPI)
     into  the  disk  directory  you  have  set  up  as   the   APLSF-10
     distribution directory.
        
           From save set "REL LIBRARY"  

                APLS12.REL
                APLG12.REL
                APLW12.REL
                APLS12.LNK
                APLG12.LNK
                APLW12.LNK

     An indirect  command  file  to  perform  this  operation  has  been
     included  in  the  installation  save set on this patch tape.  This
     file will restore the appropriate files to DSKP:[7,6,APL].  If  you
     wish  to use this command file, but are not using DSKP:[7,6,APL] as
     your distribution directory you will have to edit this command file
     to change the /RESTORE command to correspond to your directory.
        
        To use this command file, issue the following commands:
        
        .R BACKUP
        /TAPE tape:
        /@DSKP:APL1S2.CCL[7,6]
        

     The Patch and Build control file for the re-build of  this  product
     as  well  as the Autopatch product description file are supplied in
     the Installation Save-set on the  Autopatch  tape.   See  the  last
     section  of  this  document  for a list of these files.  There is a
     BACKUP command file provided  in  the  first  Save-set  which  will
     restore  these  files  to  the  proper  directory.   See the README
     documentation file in the first Save-set for more information.
                                                                  Page 9


     3.4  PREPARING FOR AUTOPATCHING COBOL-10

     Before preparing this product for Autopatching, you should  install
     the  product  on  your  system  as  described  in  the installation
     documentation supplied on the product  distribution  tape.   Unless
     the  product is correctly installed, you will not be able to SELECT
     it for Autopatching.

     The disk directory in which you have installed the executable files
     for  COBOL-10 is referred to as the product installation directory.
     In most cases  this  will  be  [1,4]  or  one  of  the  directories
     belonging to SYS:.  This directory must contain the files:
        
                for Cobol-74    for 68 to 74 translation tool

     COBDDT.REL CBL74.EXE       68274.EXE
     CPYLIB.EXE CBL74C.EXE *    68274C.EXE *
     ISAM.EXE   CBL74D.EXE *    68274D.EXE *
     LIBARY.EXE CBL74E.EXE *    68274E.EXE *
     RERUN.EXE  CBL74O.EXE *
                CBL74K.EXE *    68274K.EXE *
                CBL74F.EXE *    68274F.EXE *
                C74LIB.REL
                C74O12.EXE

        * only if using the multi-segmented compiler (ONESEG==0)

     The COBOL V12C product may be patched via source file updates  with
     re-build  and/or  via  encrypted  EXE/REL file replacement.  If you
     desire to use encryption then KEY files must be retrieved from  the
     COBOL distribution tape.  You will need to copy the following files
     from the COBOL-10 V12C distribution tape BB-H580E-SB into the  disk
     directory you have set up as the COBOL-10 distribution directory.
     COBDDT.KEY CBL74.KEY       68274.KEY
     CPYLIB.KEY CBL74C.KEY      68274C.KEY  
     ISAM.KEY   CBL74D.KEY      68274D.KEY  
     LIBARY.KEY CBL74E.KEY      68274E.KEY  
     RERUN.KEY  CBL74O.KEY  
                CBL74K.KEY      68274K.KEY  
                CBL74F.KEY      68274F.KEY  
                C74LIB.KEY
                C74O12.KEY


     If you desire to Autopatch COBOL via updated sources the  following
     files  are  required  to  build  the  COBOL  product.  They must be
     available either in the patching area (PAT:), the distribution area
     (DIS:), or in the installation area (INS:).

        From the first save-set of the Autopatch tape

        HELPER.REL      MACTEN.UNV      UUOSYM.UNV

     These files will be moved from the Autopatch tape when you use  one
     of the BACKUP CCL files described in the README file.
                                                                 Page 10


     You will need  to  copy  the  following  files  from  the  COBOL-10
     distribution  tape BB-H580E-SB into the disk directory you have set
     up as the COBOL-10 distribution directory.
        
        From save set "COBOL-Source"
        
        ACCEPT.MAC      ALBSTB.MAC      ALF.MAC         ARGS.MAC
        ASCEBC.MAC      ASCSIX.MAC      BISGEN.MAC      BTREE.MAC
        CANCEL.MAC      CBLIO.MAC       CDD.MAC         CHREQV.MAC
        CLEANC.MAC      CLEAND.MAC      CLEANT.MAC      CLRNAM.MAC
        CMNGEN.MAC      CMP.MAC         COBCOM.MAC      COBDDT.MAC
        COBFUN.MAC      COBOLA.MAC      COBOLB.MAC      COBOLC.MAC
        COBOLD.MAC      COBOLE.MAC      COBOLF.MAC      COBOLG.MAC
        COBOLK.MAC      COBOLO.MAC      COBST.MAC       COBTST.MAC
        COBVER.MAC      COMPD.MAC       COMUNI.MAC      COVRLY.MAC
        CPYLIB.MAC      CTREE.MAC       DEBSTB.MAC      DIAGS.MAC
        DIV11.MAC       DPADD.MAC       DPDIV.MAC       DPMUL.MAC
        DPSUB.MAC       DSORT.MAC       DSPFP.MAC       DTREE.MAC
        EASTBL.MAC      EBCASC.MAC      EDIT.MAC *      EDITB.MAC
        EXAM.MAC        EXPGEN.MAC      EXPON.MAC       FIX.MAC
        FLGDF.MAC       FLOAT.MAC       FNDPOP.MAC      FTDEFS.MAC
        GC.MAC          GD.MAC          GETASY.MAC      GETCPY.MAC
        GETGEN.MAC      GETITM.MAC      GETTAG.MAC      HANDAN.MAC
        IFGEN.MAC       IMPURE.MAC      INSPEC.MAC      INTERM.MAC
        IOGEN.MAC       IOTMP.MAC       IOTMPU.MAC      IPCGEN.MAC
        ISAM.MAC        KEY.MAC         KPROG.MAC       LBLERR.MAC
        LBLPRM.MAC      LCM10.MAC       LCMIPC.MAC      LIBARY.MAC
        LIBREL.MAC      LIBSHR.MAC      LILOWS.MAC      LINE.MAC
        LSU.MAC         MAGNEG.MAC      MATGEN.MAC      MESGEN.MAC
        METIO.MAC       METUNV.MAC      MMANGR.MAC      MMANGU.MAC
        MOVE.MAC        MOVGEN.MAC      MSCGEN.MAC      NSTRNG.MAC
        NTBSTB.MAC      NUBSTB.MAC      NUM.MAC         NUMEQV.MAC
        OPCTAB.MAC      OSTRNG.MAC      P.MAC           PC.MAC
        PD.MAC          PERF.MAC        PMATCH.MAC      PNZ.MAC
        PSCAN.MAC       PURAB.MAC       PURE.MAC        PUREC.MAC
        PURED.MAC       PUREE.MAC       PUREO.MAC       PURFG.MAC
        PUTAS1.MAC      PUTAS2.MAC      PUTAS3.MAC      PUTBIN.MAC
        PUTCPY.MAC      PUTERA.MAC      PUTGEN.MAC      PUTLST.MAC
        PUTRES.MAC      REMOVL.MAC      RERUN.MAC       RESOLV.MAC
        RMSIO.MAC       RPWGEN.MAC      SETRET.MAC      SIZ23.MAC
        SIZE1.MAC       SPAC.MAC        SQUIRL.MAC      SRTCRF.MAC
        SRTGEN.MAC      STINFL.MAC      STRGEN.MAC      SUBSCR.MAC
        TABLES.MAC      TODAY.MAC       TRACED.MAC      TRACER.MAC
        TRYNAM.MAC      USRDSP.MAC      XFRGEN.MAC      XPAND.MAC
        XPNPPL.MAC      ZERC.MAC
        RMSINT.UNV

        CMLSYM.MAC      DBDML.MAC       DBGETF.MAC      DBSDCL.MAC
        DMLERR.MAC      DMLIO.MAC       DMLVOK.MAC      GENDCL.MAC
        STRDCL.MAC      STRUNV.MAC      COBASM.MAC

        If building DBMS into the OTS:

        SCHIO1.REL      STRHI.REL

                                                                 Page 11


        *NOTE* EDIT.MAC is renamed as EDITC.MAC in the distribution area


     An indirect  command  file  to  perform  this  operation  has  been
     included  in  the  installation  save set on this patch tape.  This
     file will restore the appropriate files to DSKP:[7,6,CBL].  If  you
     wish  to use this command file, but are not using DSKP:[7,6,CBL] as
     your distribution directory you will have to edit this command file
     to change the /RESTORE command to correspond to your directory.
        
     To use this command file, issue the following commands:
        
        .R BACKUP
        /TAPE tape:
        /@DSKP:CBL12C.CCL[7,6]
                for source file updating

        .R BACKUP
        /TAPE tape:
        /@DSKP:CBR12C.CCL[7,6]
                for EXE/REL replacement updating
        
     Use of any of these files will also restore the SORT files  on  the
     COBOL  tape  to  the DSKP:[7,6,SRT] area.  Also the following files
     are restored by these CCL files but not used by Autopatch:

        CRELD.MAC       GETERA.MAC      SETEOF.MAC      SRTTAB.MAC
        STRNGL.MAC

     If you will be Autopatching BOTH Cobol-74 and the 68274 Translation
     Tool  new files are required in the patching directory.  Obtain the
     COBASM.MAC file and make a copy named C74ASM.MAC.  You must  create
     a  copy  of  the COBASM.MAC file with the FT68274 switch set on and
     call it TRNASM.MAC.  For more information refer to section  6.0  of
     the COBOL.INS file on the COBOL 12C distribution tape.

     Do not eliminate the COBASM.MAC file -  the  selection  process  of
     Autopatch requires this file to be present in the DIS:  directory.

     When SELECTing COBOL with PEP you will be asked if  you  are  using
     the  multi-seg  compiler.  Unless you have set the ONESEG switch on
     in the COBASM.MAC file the correct answer is YES.  In order to have
     Autopatch  include  the  SORT  module in the OTS you must create an
     empty file named CBLSRT.FLG in the patching directory  (PAT:).   If
     the   process  can  find  CBLSRT.REL  it  will  then  be  included.
     Likewise, in order to have Autopatch include support  for  DBMS  in
     the  OTS  you  must  create  an  empty file named CBLDBM.FLG in the
     patching directory.

     The Patch and Build control file for the re-build of  this  product
     as  well  as the Autopatch product description file are supplied in
     the Installation Save-set on the  Autopatch  tape.   See  the  last
     section  of  this  document  for a list of these files.  There is a
     BACKUP command file provided  in  the  first  Save-set  which  will
     restore  these  files  to  the  proper  directory.   See the README
                                                                 Page 12


     documentation file in the first Save-set for more information.
                                                                 Page 13


     3.5  PREPARING FOR AUTOPATCHING DBMS-10

     Before preparing this product for Autopatching, you should  install
     the  product  on  your  system  as  described  in  the installation
     documentation supplied on the product  distribution  tape.   Unless
     the  product is correctly installed, you will not be able to SELECT
     it for Autopatching.

     The disk directory in which you have installed the executable files
     for  DBMS-10  is referred to as the product installation directory.
     In most cases  this  will  be  [1,4]  or  one  of  the  directories
     belonging to SYS:.  This directory must contain the files:
        
                SCHEMA.EXE
                FORDML.EXE
                DBMEND.EXE
                DBINFO.EXE
                DAEMDB.EXE

     The following files are required to build the DBMS  product.   They
     must   be  available  either  in  the  patching  area  (PAT:),  the
     distribution area (DIS:), or in the installation area (INS:).

        From the first save-set of the Autopatch tape

        HELPER.REL      SCAN.REL

     These files will be moved from the Autopatch tape when you use  one
     of the BACKUP CCL files described in the README file.

     You will  need  to  copy  the  following  files  from  the  DBMS-10
     distribution  tape  BB-D478D-BB(1600  BPI)  or AP-C804D-BB(800 BPI)
     into the disk directory you have set up as the DBMS-10 distribution
     directory.
        
        From save set DBMS-SOURCE
        
                DAB10.REL       FMLANY.REL
                DABANY.REL      GENIO1.REL
                DBS10.REL       GENME1.REL
                DBSANY.REL      GENMS1.REL
                DBSCOB.REL      INF10.REL
                DBSDCL.REL      INFANY.REL
                DBSFOR.REL      MND10.REL
                DDL10.REL       MNDANY.REL
                DDLANY.REL      SCHIO1.REL
                FML10.REL       STRHI.REL

                DAEMD1.CMD
                DBINF1.CMD
                DBMEN1.CMD
                FORDM1.CMD
                SCHEM1.CMD

     An indirect  command  file  to  perform  this  operation  has  been
                                                                 Page 14


     included  in  the  installation  save set on this patch tape.  This
     file will restore the appropriate files to DSKP:[7,6,DBM].  If  you
     wish  to use this command file, but are not using DSKP:[7,6,DBM] as
     your distribution directory you will have to edit this command file
     to change the /RESTORE command to correspond to your directory.
        
        To use this command file, issue the following commands:
        
        .R BACKUP
        /TAPE tape:
        /@DSKP:DBMV5A.CCL[7,6]
        

     The Patch and Build control file for the re-build of  this  product
     as  well  as the Autopatch product description file are supplied in
     the Installation Save-set on the  Autopatch  tape.   See  the  last
     section  of  this  document  for a list of these files.  There is a
     BACKUP command file provided  in  the  first  Save-set  which  will
     restore  these  files  to  the  proper  directory.   See the README
     documentation file in the first Save-set for more information.
                                                                 Page 15


     3.6  PREPARING FOR AUTOPATCHING CUSTOMER SUPPORTED Monitor Modules

     You will need to copy the following files from  the  TOPS-10  V7.04
     Customer  Supported  distribution  tape  BB-X130C-SB  into the disk
     directory you have set up as the MONITOR-10 distribution directory.
        
           From the second save set

        CCIINT.MAC      CDPSER.MAC      CDRSER.MAC      D6DINT.MAC
        D76INT.MAC      D78INT.MAC      D85INT.MAC      D8RINT.MAC
        DISSER.MAC      DLSINT.MAC      DPXKON.MAC      DSXKON.MAC
        DTASER.MAC      FHXKON.MAC      FSXKON.MAC      FTDLS1.MAC
        KASER.MAC       METCON.MAC      PLTSER.MAC      PPSSER.MAC
        PRSSER.MAC      PTPSER.MAC      PTRSER.MAC      RX2SER.MAC
        SAXPRM.MAC      SAXSER.MAC      TCXKON.MAC      TMXKON.MAC
        TS1KON.MAC      TYPSER.MAC      VBCSER.MAC      XTCSER.MAC
        UNSUP.FIL

     An indirect  command  file  to  perform  this  operation  has  been
     included  in  the  installation  save set on this patch tape.  This
     file will restore the appropriate files to DSKP:[7,6,MON].  If  you
     wish  to use this command file, but are not using DSKP:[7,6,MON] as
     your distribution directory you will have to edit this command file
     to change the /RESTORE command to correspond to your directory.
        
        To use this command file, issue the following commands:
        
        .R BACKUP
        /TAPE tape:
        /@DSKP:CUS704.CCL[7,6]
        

     The Autopatch product description file for this product is supplied
     in  the  Installation Save-set on the Autopatch tape.  See the last
     section of this document for a listing of this file.   There  is  a
     BACKUP  command  file  provided  in  the  first Save-set which will
     restore  this  file  to  the  proper  directory.   See  the  README
     documentation file in the first Save-set for more information.
                                                                 Page 16


     3.7  PREPARING FOR AUTOPATCHING DECNET

     Before preparing this product for Autopatching, you should  install
     the  product  on  your  system  as  described  in  the installation
     documentation supplied on the product  distribution  tape.   Unless
     the  product is correctly installed, you will not be able to SELECT
     it for Autopatching.

     The disk directory in which you have installed the executable  file
     for  DECNET-10-V704  is  referred  to  as  the product installation
     directory.  In most  cases  this  will  be  [1,4]  or  one  of  the
     directories  belonging  to  SYS:.   This directory must contain the
     NML.EXE file.

     You will need to copy the following file from  the  TOPS-10  DECNET
     7.04 distribution tape BB-X116C-SB into the disk directory you have
     set up as the DECNET-10 distribution directory.
        
           From the first save set

                NML.KEY

     An indirect  command  file  to  perform  this  operation  has  been
     included  in  the  installation  save set on this patch tape.  This
     file will restore the appropriate files to  DSKP:[7,6,DECNET].   If
     you   wish   to   use   this   command  file,  but  are  not  using
     DSKP:[7,6,DECNET] as your distribution directory you will  have  to
     edit this command file to change the /RESTORE command to correspond
     to your directory.
        
        To use this command file, issue the following commands:
        
        .R BACKUP
        /TAPE tape:
        /@DSKP:DEC704.CCL[7,6]
        

     The Autopatch product description file for this product is supplied
     in  the  Installation Save-set on the Autopatch tape.  See the last
     section of this document for a listing of this file.   There  is  a
     BACKUP  command  file  provided  in  the  first Save-set which will
     restore  this  file  to  the  proper  directory.   See  the  README
     documentation file in the first Save-set for more information.
                                                                 Page 17


     3.8  PREPARING FOR AUTOPATCHING FORTRAN-10

     Before preparing this product for Autopatching, you should  install
     the  product  on  your  system  as  described  in  the installation
     documentation supplied on the product  distribution  tape.   Unless
     the  product is correctly installed, you will not be able to SELECT
     it for Autopatching.

     The disk directory in which you have installed the executable files
     for   FORTRAN-10   is  referred  to  as  the  product  installation
     directory.  In most  cases  this  will  be  [1,4]  or  one  of  the
     directories  belonging  to  SYS:.   This directory must contain the
     files:
        
        FORTRA.EXE      SINGLE.EXE      FORTB.EXE       FORTC.EXE
        FORTD.EXE       FORTE.EXE       FORTF.EXE       FORTG.EXE
        DORTRA.EXE      DORTB.EXE       DOTRC.EXE       DORTD.EXE
        DORTE.EXE       DORTF.EXE       DORTG.EXE       FORO11.EXE
        FORLIB.REL      FORDDT.REL

     The FORTRAN V11 product may be patched via source file updates with
     re-build  and/or  via  encrypted  EXE/REL file replacement.  If you
     desire to use encryption then KEY files must be retrieved from  the
     FORTRAN  distribution  tape.   You  will need to copy the following
     files from the FORTRAN-10 V11 distribution  tape  BB-D480G-SB  into
     the  disk  directory you have set up as the FORTRAN-10 distribution
     directory.

        From the save set "FORTRAN-AUTOPATCH"   
        FORTRA.KEY      SINGLE.KEY      FORTB.KEY       FORTC.KEY
        FORTD.KEY       FORTE.KEY       FORTF.KEY       FORTG.KEY
        DORTRA.KEY      DORTB.KEY       DOTRC.KEY       DORTD.KEY
        DORTE.KEY       DORTF.KEY       DORTG.KEY       FORO11.KEY
        FORLIB.KEY      FORDDT.KEY

     If you  are  also  using  DBMS  with  FORTRAN  you  will  need  the
     FORDBM.REL  file  from  the  fourth  save-set  of  the  FORTRAN v11
     distribution tape and the DBCS1F.CMD file from the second  save-set
     of the Autopatch tape.

     If  you  desire  to  Autopatch  FORTRAN  via  updated  sources  the
     following  files  are  required to build the FORTRAN product.  They
     must  be  available  either  in  the  patching  area  (PAT:),   the
     distribution area (DIS:), or in the installation area (INS:).

        From the first save-set of the Autopatch tape

        GLXMAC.UNV      HELPER.REL      MACTEN.UNV      QSRMAC.UNV
        RMSINT.UNV      SCAN.REL        SCNMAC.UNV      UUOSYM.UNV


     These files will be moved from the Autopatch tape when you use  one
     of the BACKUP CCL files described in the README file.

     You will need to copy  the  following  files  from  the  FORTRAN-10
                                                                 Page 18


     distribution  tape BB-D480G-SB into the disk directory you have set
     up as the FORTRAN-10 distribution directory.
        
        From save set FORTRAN-OTS-DEBUGGER

        F10REL.MAC      FDBMH5.MAC      FDBML5.MAC      FDBML6.MAC
        FDDT.MAC        FORBOT.MAC      FORCHR.MAC      FORCNV.MAC
        FORCOM.MAC      FORDBM.MAC      FORDDT.MAC      FORDST.MAC
        FORDUM.MAC      FORERR.MAC      FORFMT.MAC      FORHST.MAC
        FORINI.MAC      FORIO .MAC      FORMEM.MAC      FORMSC.MAC
        FORMSG.MAC      FORNML.MAC      FOROP .MAC      FOROPN.MAC
        FOROTS.MAC      FORPL2.MAC      FORPRM.MAC      FORPSE.MAC
        FORRMS.MAC      FORRTF.MAC      FORSRT.MAC      FORXIT.MAC
        M10REL.MAC      MTHARG.MAC      MTHCDX.MAC      MTHCGX.MAC
        MTHCNV.MAC      MTHCPX.MAC      MTHDBL.MAC      MTHDUM.MAC
        MTHGDB.MAC      MTHHST.MAC      MTHMSG.MAC      MTHPRM.MAC
        MTHSNG.MAC      MTHTRP.MAC
        F10LIB.CCL      F10OTS.CCL      FDBM5 .CCL
        FORPL1.FOR

        From save set FORTRAN-COMPILER
        
        ACT0  .BLI      ACT1  .BLI      ALCBLO.BLI      ARRXPN.BLI
        ASHELP.BLI      BLIO  .BLI      BUILD .BLI      CANNON.BLI
        CGDO  .BLI      CGEXPR.BLI      CGSTMN.BLI      CMPBLO.BLI
        CMPLEX.BLI      CODETA.BLI      COMSUB.BLI      DATAST.BLI
        DEBUG .BLI      DEFLT .BLI      DEFPT .BLI      DOALC .BLI
        DOXPN .BLI      DRIVER.BLI      ERROR0.BLI      ERROUT.BLI
        ERROVA.BLI      ERROVB.BLI      ERROVC.BLI      ERROVD.BLI
        ERROVG.BLI      ERROVR.BLI      EXPRES.BLI      FAZ1  .BLI
        FIRST .BLI      FMTLEX.BLI      FORMAT.BLI      GCMNSB.BLI
        GLOBAL.BLI      GNRCFN.BLI      GOPT2 .BLI      GOPTIM.BLI
        GRAPH .BLI      INOUT .BLI      INPT  .BLI      IOFLG .BLI
        IOPT  .BLI      LEFT72.BLI      LEFTFM.BLI      LEXAID.BLI
        LEXICA.BLI      LEXNAM.BLI      LEXSUP.BLI      LISTNG.BLI
        LISTOU.BLI      MAIN  .BLI      MEMCMP.BLI      MOVA  .BLI
        NUMIO1.BLI      OPTAB .BLI      OPTMAC.BLI      OUTMOD.BLI
        OUTZ  .BLI      P2S1  .BLI      P2S2  .BLI      P3R   .BLI
        PEEPOP.BLI      PH2S  .BLI      PH3G  .BLI      PHA2  .BLI
        PHA3  .BLI      PNROPT.BLI      REGAL2.BLI      REGUTL.BLI
        RELBUF.BLI      REQREL.BLI      SCAN0 .BLI      SCNR  .BLI
        SKSTMN.BLI      SRCA  .BLI      STA0  .BLI      STA1  .BLI
        STA2  .BLI      STA3  .BLI      STREGA.BLI      TABLES.BLI
        TBL   .BLI      TRACE1.BLI      TSTR  .BLI      UNEND .BLI
        UTIL  .BLI      VER5  .BLI      VLTPPR.BLI      
        CNSTCM.MAC      COMMAN.MAC      DGCMN .MAC      DNPT  .MAC
        DOPT  .MAC      ERR3  .MAC      ERRTB3.MAC      EXOSUP.MAC
        FLTGEN.MAC      GFOPDF.MAC      JOBD  .MAC      OPGNTA.MAC
        OWNDM .MAC      QTAB1 .MAC      REVHST.MAC
        A     .CMD      ALL   .CMD      B     .CMD      BLD   .CMD
        C     .CMD      D     .CMD      E     .CMD      F     .CMD
        G     .CMD      DA    .CMD      DB    .CMD      DC    .CMD
        DD    .CMD      DE    .CMD      DF    .CMD      DG    .CMD
        LEFT72.CMD      LEFTFM.CMD      
        F72BNF.SYN      FRMBNF.SYN      
                                                                 Page 19



        From save set FORTRAN-TOOLS 
        
        BLIS10.ERR      BLIS10.EXE      QSRMC2.UNV


     An indirect  command  file  to  perform  this  operation  has  been
     included  in  the  installation  save set on this patch tape.  This
     file will restore the appropriate files to DSKP:[7,6,FTN].  If  you
     wish  to use this command file, but are not using DSKP:[7,6,FTN] as
     your distribution directory you will have to edit this command file
     to change the /RESTORE command to correspond to your directory.
        
        To use this command file, issue the following commands:
        
        .R BACKUP
        /TAPE tape:
        /@DSKP:FTN111.CCL[7,6]
                for source file updating

        .R BACKUP
        /TAPE tape:
        /@DSKP:FTN1X1.CCL[7,6]
                for EXE/REL replacement updating
        

     If you use DBMS with FORTRAN and want to have the  Autopatch  Patch
     and  Build Control file build DBMSF you must create a dummy file in
     the patching directory (PAT:) called FTNDBM.FLG.  The  presence  of
     this  file  on PAT:  will cause the BATCH control file to branch in
     order to perform the processing required to build  DBMSF.EXE.   You
     will  also need the DBCS1F.CMD file from the second save-set of the
     Autopatch tape.

     The Patch and Build control file and utility command files for  the
     re-build   of  this  product  as  well  as  the  Autopatch  product
     description file are supplied in the Installation Save-set  on  the
     Autopatch  tape.   See the last section of this document for a list
     of these files.  There is a BACKUP command  file  provided  in  the
     first  Save-set  which  will  restore  these  files  to  the proper
     directory.  See the README documentation file in the first Save-set
     for more information.
                                                                 Page 20


     3.9  PREPARING FOR AUTOPATCHING GALAXY-10

     Before preparing this product for Autopatching, you should  install
     the  product  on  your  system  as  described  in  the installation
     documentation supplied on the product  distribution  tape.   Unless
     the  product is correctly installed, you will not be able to SELECT
     it for Autopatching.

     The disk directory in which you have installed the executable files
     for GALAXY-10 is referred to as the product installation directory.
     In most cases  this  will  be  [1,4]  or  one  of  the  directories
     belonging to SYS:.  This directory must contain the files:
        
                BATCON.EXE      NEBULA.EXE
                CATCNV.EXE      OPR.EXE
                CATLOG.EXE      ORION.EXE
                CDRIVE.EXE      PLEASE.EXE
                GALGEN.EXE      PULSAR.EXE
                GLXLIB.EXE      QUASAR.EXE
                GLXLIB.REL      QUEUE.EXE
                LPTSPL.EXE      SPRINT.EXE
        
                CATTAB.REL      OPRPAR.REL
                CHRFRM.REL      ORNMAC.UNV
                GALCNF.MAC      QSRMAC.UNV
                GALCNF.UNV      QUOTAB.REL
                GLXMAC.UNV

     The following files are required to build the GALAXY product.  They
     must   be  available  either  in  the  patching  area  (PAT:),  the
     distribution area (DIS:), or in the installation area (INS:).

        From the first save-set of the Autopatch tape

        ACTLIB.REL      ACTSYM.UNV      BTSPRM.UNV      CATPRM.UNV
        CATTAB.REL      D60JSY.REL      D60UNV.UNV      HELPER.REL
        LCPORN.REL      LCPTAB.REL      SCAN.REL        SCNMAC.UNV
        UFDPRM.UNV      UFDSET.REL      UUOSYM.UNV      WILD.REL

     These files will be moved from the Autopatch tape when you use  one
     of the BACKUP CCL files described in the README file.

     You will need to copy the following files  from  the  TOPS-10  7.04
     CUSP distribution tape BB-XXXXX-BB into the disk directory you have
     set up as the GALAXY-10 distribution directory.
        
        BATCON.MAC      BATCTL.MAC      BATLOG.MAC      BATMAC.MAC
        BATPTY.MAC      BATUSR.MAC      CDRIVE.MAC      CNFHDW.MAC
        CNFORN.MAC      CNFTAB.MAC      DRIVRS.CCL      GALGEN.MAC
        GLXCOM.MAC      GLXFIL.MAC      GLXFUN.MAC      GLXINI.MAC
        GLXINT.MAC      GLXIPC.MAC      GLXKBD.MAC      GLXLNK.MAC
        GLXMAC.MAC      GLXMEM.MAC      GLXOTS.MAC      GLXSCN.MAC
        GLXTXT.MAC      GLXUTL.MAC      GLXVER.MAC      LCPORN.MAC
        LCPTAB.MAC      LPTD60.MAC      LPTL01.MAC      LPTL03.MAC
        LPTLP5.MAC      LPTMAC.MAC      LPTMTA.MAC      LPTSPL.MAC
                                                                 Page 21


        LPTTTY.MAC      OPR.MAC         OPRCMD.MAC      OPRERR.MAC
        OPRLOG.MAC      OPRNET.MAC      OPRPAR.MAC      OPRQSR.MAC
        ORION.MAC       ORNMAC.MAC      PLEASE.MAC      PLRDSK.MAC
        PLRDSP.MAC      PLRDTA.MAC      PLRINI.MAC      PLRLBP.MAC
        PLRMAC.MAC      PLROPR.MAC      PLRQUO.MAC      PLRT10.MAC
        PLRTAP.MAC      PULSAR.MAC      QSRADM.MAC      QSRALC.MAC
        QSRCAT.MAC      QSRDSP.MAC      QSRFSS.MAC      QSRINF.MAC
        QSRIPC.MAC      QSRMAC.MAC      QSRMDA.MAC      QSRMEM.MAC
        QSRNET.MAC      QSRQUE.MAC      QSRSCH.MAC      QSRT10.MAC
        QUASAR.MAC      QUEUE.MAC       QUOPRM.MAC      QUOTAB.MAC
        SPRINT.MAC

     An indirect  command  file  to  perform  this  operation  has  been
     included  in  the  installation  save set on this patch tape.  This
     file will restore the appropriate files to DSKP:[7,6,CSP].  If  you
     wish  to use this command file, but are not using DSKP:[7,6,CSP] as
     your distribution directory you will have to edit this  command  to
     change the /RESTORE command to correspond to your directory.
        
        To use this command file, issue the following commands:
        
        .R BACKUP
        /TAPE tape:
        /@DSKP:CSP704.CCL[7,6]
        

     The Patch and Build control file for the re-build of  this  product
     as  well  as the Autopatch product description file are supplied in
     the Installation Save-set on the  Autopatch  tape.   See  the  last
     section  of  this  document  for a list of these files.  There is a
     BACKUP Retrieval Command File provided in the first Save-set  which
     will  restore  these files to the proper directory.  See the README
     documentation file in the first Save-set for more information.
                                                                 Page 22


     3.10  PREPARING FOR AUTOPATCHING IBMCOM-10

     Before preparing this product for Autopatching, you should  install
     the  product  on  your  system  as  described  in  the installation
     documentation supplied on the product  distribution  tape.   Unless
     the  product is correctly installed, you will not be able to SELECT
     it for Autopatching.

     The disk directory in which you have installed the executable files
     for IBMCOM-10 is referred to as the product installation directory.
     In most cases  this  will  be  [1,4]  or  one  of  the  directories
     belonging to SYS:.  This directory must contain the files:
                                        HASP only

                D6LQ3.BIN               D6LQH.BIN
                D6LQ3.EXE               D6LQH.EXE
                D6LQ3D.BIN              D6LQHD.BIN
                D6LQ3D.EXE              D6LGHD.EXE

                D6TK3.BIN               D6TKH.BIN
                D6TK3.EXE               D6TKH.EXE
                D6TK3D.BIN              D6TKHD.BIN
                D6TK3D.EXE              D6TKHD.EXE

                D6TQ3.BIN               D6TQH.BIN
                D6TQ3.EXE               D6TQH.EXE
                D6TQ3D.BIN              D6TQHD.BIN
                D6TQ3D.EXE              D6TQHD.EXE

                IBMSPL.EXE

                D60SPD.EXE

     The following files are required to build the IBMCOM product.  They
     must   be  available  either  in  the  patching  area  (PAT:),  the
     distribution area (DIS:), or in the installation area (INS:).

        From the first save-set of the Autopatch tape

        ACTSYM.UNV      D60JSY.REL      D60UNV.UNV      GLXLIB.REL
        GLXMAC.UNV      HELPER.REL      JOBDAT.UNV      MACTEN.UNV
        ORNMAC.UNV      QSRMAC.UNV      UUOSYM.UNV

     These files will be moved from the Autopatch tape when you use  one
     of the BACKUP CCL files described in the README file.

     From a GALAXY build or installation you must  have  the  GALCNF.UNV
     file available in PAT:, DIS:, or INS:.

     You will need to copy the following files from the  TOPS-10  IBMCOM
     distribution  tape  BB-J992D-SB (ET) or BB-V552B-SB (HASP) into the
     disk directory you  have  set  up  as  the  IBMCOM-10  distribution
     directory.
                                HASP only
        
                                                                 Page 23


        10TK3.P11               10TKH.P11
        CHK60.P11
        D60SPD.MAC
        D6LQ3.P11               D6LQH.P11
        D6TQ3.P11               D6TQH.P11
        DEBUG.P11
        HBSC.P11
        IBMMAC.MAC
        IBMPAT.MAC
        IBMSPL.MAC
        IBMUSR.MAC
        INIT.P11
        INIT1.P11
        INIT2.P11
        LINDRV.P11
            *MACROS.P11
        MDCODE.P11
        MININT.P11
        MSGHDL.P11
        PROD.P11
        QUEING.P11
        S60.P11
        STGMAN.P11
        TRNTAB.P11
        XDEFIN.P11
        XDTE10.P11
        XDISPA.P11
        XDL10.P11
        XL3780.P11              XLHASP.P11
        XTENCM.P11

        DDT11.EXE
        MACDLX.EXE

      * Renamed as MACRO.P11 in the distribution directory

     An indirect  command  file  to  perform  this  operation  has  been
     included  in  the  installation  save set on this patch tape.  This
     file will restore the  appropriate  files  to  DSKP:[7,6,IBMET]  or
     DSKP:[7,6,IBMHSP].   If  you wish to use this command file, but are
     not using the indicated SFD as your distribution directory you will
     have  to  edit  this command file to change the /RESTORE command to
     correspond to your directory.  If you do not use this command  file
     then  the  MACROS.P11  file  in  the distribution directory must be
     renamed or copied  to  be  MACRO.P11  before  the  product  can  be
     SELECTED.
        
        To use this command file, issue the following commands:
        
        .R BACKUP
        /TAPE tape:
        /@DSKP:IETV04.CCL[7,6]  for IBMCOM-10-ET-V4
                or
        /@DSKP:IHSV01.CCL[7,6]  for IBMCOM-10-HASP-V1
        
                                                                 Page 24


     The Patch and Build control file for the re-build of  this  product
     as  well  as the Autopatch product description file are supplied in
     the Installation Save-set on the  Autopatch  tape.   See  the  last
     section  of  this  document  for a list of these files.  There is a
     BACKUP command file provided  in  the  first  Save-set  which  will
     restore  these  files  to  the  proper  directory.   See the README
     documentation file in the first Save-set for more information.
                                                                 Page 25


     3.11  PREPARING FOR AUTOPATCHING MCB-10


     Before preparing this product for Autopatching,  you  MUST  install
     the  product  on  your system as described in the DECnet-10 Network
     Generation and  Installation  Procedures  Manual  (AA-P379A-TB)  in
     Notebook  20  of  the  TOPS-10 Notebook set.  Unless the product is
     correctly installed,  you  will  not  be  able  to  SELECT  it  for
     Autopatching.

     The disk directory in which you have installed the executable files
     for  MCB-10  is  referred to as the product installation directory.
     In most cases  this  will  be  [1,4]  or  one  of  the  directories
     belonging to SYS:.  This directory must contain the files:

        DNMAC.EXE
        DTEDMP.SYS
        DTEMPS.SYS
        DTEMPT.SYS
        NETGEN.EXE
        NIPGEN.EXE
        TKB36.EXE
        VNP36.EXE
        nodename.SYS

     nodename.SYS is the front end system file with your node name

     The following files are required to build the  MCB  product.   They
     must   be  available  either  in  the  patching  area  (PAT:),  the
     distribution area (DIS:), or in the installation area (INS:).

        From the first save-set of the Autopatch tape

        GLXMAC.UNV      ORNMAC.UNV      MACSYM.UNV      UUOSYM.UNV
        GLXLIB.REL

     These files will be moved from the Autopatch tape when you use  one
     of the BACKUP CCL files described in the README file.

     You will need to copy all of the files in the first save set of the
     TOPS-10  DECNET  7.04  distribution  tape BB-X116C-SB into the disk
     directory you have set up as  the  MCB-10  distribution  directory.
     These files should already exist in a disk directory as part of the
     original DECNET-10 installation.  If not, they  are  on  the  first
     save set on the distribution tape.
             
             From the first save set - MCB MODULES
             
        CEX.KEY         CEX.STB         CEX.TSK
        CEXCOM.KEY      CEXCOM.STB      CEXCOM.TSK
        DCP.KEY         DCP.STB         DCP.TSK
        DMC.KEY         DMC.STB         DMC.TSK
        DMR.KEY         DMR.STB         DMR.TSK
        DTE.KEY         DTE.STB         DTE.TSK
        DTR.KEY         DTR.STB         DTR.TSK
                                                                 Page 26


        INI.KEY         INI.STB         INI.TSK
        KDP.KEY         KDP.STB         KDP.TSK
        MDT.KEY         MDT.STB         MDT.STK
        NDT.KEY         NDT.STB         NDT.TSK
        NML.KEY         NML.STB         NML.TSK
        NMS.KEY         NMS.STB         NMS.TSK
        NMX.KEY         NMX.STB         NMX.TSK
        NS1.KEY         NS1.STB         NS1.TSK
        NS2.KEY         NS2.STB         NS2.TSK
        NSP.KEY         NSP.STB         NSP.TSK
        RSX11S.KEY      RSX11S.STB      RSX11S.TSK
        SC.KEY          SC.STB          SC.TSK
        SC1.KEY         SC1.STB         SC1.TSK
        SCX.KEY         SCX.STB         SCX.TSK
        TLI.KEY         TLI.STB         TLI.TSK
        TOP.KEY         TOP.STB         TOP.TSK
        XPE.KEY         XPE.STB         XPE.TSK
        XPT.KEY         XPT.STB         XPT.TSK         RSXMS.STB
             CEXLIB.M11      CEXLLC.M11      DATML.M11       DCPDLC.M11
             DMCDLC.M11      DMRDLC.M11      DTEDLC.M11      DTRLLC.M11
             INILLC.M11      KDPDDM.M11      MCBLIB.M11      NMTAB.M11
             NMXLLC.M11      NSTAB.M11       NSPLLC.M11      RSXLIB.M11
             SCLLC.M11       SCXLLC.M11      TOPLLC.M11      XPTLLC.M11
             MCBLIB.OLB      SYSLIB.OLB
        NGNDIA.MAC      NGNFIN.MAC      NGNCNF.MAC      NGNDAT.MAC
        NGNDEV.MAC      NETGEN.MAC      NGNMAC.MAC      NGNPRM.MAC
        NGNPRS.MAC      NIPGEN.MAC

     An indirect command control file to retrieve these files  has  been
     included  in  the  installation  save set on this patch tape.  This
     file will restore the appropriate files to  DSKP:[7,6,DECNET].   If
     you wish use this control file, but are not using DSKP:[7,6,DECNET]
     as your distribution directory you will have to edit  this  command
     file   to  change  the  /RESTORE  command  to  correspond  to  your
     directory.


        To use this command file, issue the following commands:

        .R BACKUP
        /TAPE tape:
        /@DSKP:DEC704.CCL[7,6]


     The DECNET-10 front end build also  requires  the  following  files
     from the original installation:

        CETAB.MAC
        NETPAR.MAC
        NMLACC.MAC

     The above files are NOT on the  release  tape.   They  are  created
     during  the  required  installation process.  NMLACC.MAC is deleted
     after  a  successful  front  end  build  to  protect  the   Network
     Management  Access  Control  information  it contains.  Path to the
                                                                 Page 27


     directory in which your front end was built and do the following:

        .R NETGEN
        NETGEN>RESTORE xxxxxx.CNF

        ;where xxxxxx is your front end node
        ;name.  The configuration file (.CNF)
        ;was automatically saved when you did
        ;the original installation.

        ;If your site doesn't use Network Management Access Control
        ;skip the following 3 DEFINE commands

        NETGEN>DEFINE EXECUTOR MANAGEMENT USER foo1
        NETGEN>DEFINE EXECUTOR MANAGEMENT PASSWORD foo2
        NETGEN>DEFINE EXECUTOR MANAGEMENT ACCOUNT foo2

        NETGEN>FINISH

     Copy  CETAB.MAC  and   NETPAR.MAC   into   the   MCB-10   Autopatch
     distribution  directory.   If you wish the protection of having the
     NMLACC.MAC file deleted after a successful build,  rename  it  into
     the  directory  you  have set up as the patching directory, and the
     above procedure will be required before each  Autopatch  update  of
     MCB-10.   Otherwise,  copy  NMLACC.MAC  into  the  MCB-10 Autopatch
     distribution directory.

     When SELECTing this product for Autopatching the PEP  program  will
     ask  for  the  nodename.   Use the same name as was used during the
     initial  installation.   If  your  product  installation  directory
     (INS:)  does  not  include  the  front  end  system  image, usually
     "nodename".SYS, then copy it into that directory.

     Path back to your original directory.

     The Patch and Build control file for the re-build of  this  product
     as  well  as the Autopatch product description file are supplied in
     the Installation Save-set on the  Autopatch  tape.   See  the  last
     section  of  this  document  for a list of these files.  There is a
     BACKUP command file provided  in  the  first  Save-set  which  will
     restore  these  files  to  the  proper  directory.   See the README
     documentation in the first Save-set for more information.
                                                                 Page 28


     3.12  PREPARING FOR AUTOPATCHING MONITOR-10-V704

     Before preparing this product for Autopatching, you should  install
     the  product  on  your  system  as  described  in  the installation
     documentation supplied on the product  distribution  tape.   Unless
     the  product is correctly installed, you will not be able to SELECT
     it for Autopatching.

     The disk directory in which you have installed the executable files
     for  TOPS-10  is referred to as the product installation directory.
     In most cases  this  will  be  [1,4]  or  one  of  the  directories
     belonging to SYS:.  This directory must contain the files:
        
        MON.EXE
        MONGEN.EXE
        TOPS10.REL


     The MON.EXE file is a copy of your current monitor.  The  Autopatch
     process   will   create   a   new   MON.EXE   in  the  installation
     directory(INS:).

     The following files are required  to  build  the  MONITOR  product.
     They must be available in the patching area (PAT:).

        From the first save-set of the Autopatch tape

        EDDT.REL        JOBDAT.MAC      MACSYM.MAC      UUOSYM.MAC

     These files will be moved from the Autopatch tape when you use  one
     of the BACKUP CCL files described in the README file.

     Be sure to delete any old files  for  previous  monitors  from  the
     common patching area.  This includes *.FIL and D36PAR.*.

     You will need to copy the following files  from  the  TOPS-10  7.04
     BB-X140C-SB Distribution tape, into the disk directory you have set
     up as the MONITOR-10 distribution directory.
        
        From the 7.04 MONITOR dsitribution tape
        
        APRSER.MAC      AUTCON.MAC      CD2SER.MAC      CLOCK1.MAC
        COMCON.MAC      COMDEV.MAC      COMMOD.MAC      COMMON.MAC
        CORE1.MAC       CTXSER.MAC      D36COM.MAC      D36PAR.MAC
        D60SER.MAC      D6SINT.MAC      D8EINT.MAC      D8KINT.MAC
        D8SINT.MAC      DATMAN.MAC      DCRSER.MAC      DEVPRM.MAC
        DNADDL.MAC      DLPSER.MAC      DTEPRM.MAC      DTESER.MAC
        DZINT.MAC       ERRCON.MAC      ETHPRM.MAC      ETHSER.MAC
        ETHUUO.MAC      FEDSER.MAC      FILFND.MAC      FILIO.MAC
        FILUUO.MAC      FTEJBD.MAC      IPCSER.MAC      KLPPRM.MAC
        KLPSER.MAC      KNISER.MAC      LATSER.MAC      LLINKS.MAC
        LLMOP.MAC       LLMPRM.MAC      LOKCON.MAC      LP2SER.MAC
        LPTSER.MAC      MONBTS.MAC      MONGEN.MAC      MONPFH.MAC
        MOSSER.MAC      MPXSER.MAC      MSCCOM.MAC      MSCPAR.MAC
        NETDEV.MAC      NETPRM.MAC      NETSER.MAC      NRTSER.MAC
                                                                 Page 29


        NTMAN.MAC       NULFEK.MAC      ONCMOD.MAC      PATCH.MAC
        PSISER.MAC      PTYSER.MAC      QUESER.MAC      RAXKON.MAC
        REFSTR.MAC      RHXKON.MAC      RNXKON.MAC      ROUTER.MAC
        RPXKON.MAC      RTTRP.MAC       S.MAC           SCASER.MAC
        SCAPRM.MAC      SCHED1.MAC      SCLINK.MAC      SCMUUO.MAC
        SCNSER.MAC      SCPAR.MAC       SCSUUO.MAC      SEGCON.MAC
        SWPSER.MAC      SYSINI.MAC      T78KON.MAC      TAPSER.MAC
        TAPUUO.MAC      TD2KON.MAC      TM2KON.MAC      TMPUUO.MAC
        TTDINT.MAC      TX1KON.MAC      USRONC.MAC      UUOCON.MAC
        VMSER.MAC
        COMPIL.CTL      BUILD.CTL       TREE.TEC        TOPS10.TEC
        TOPS10.FIL


     An indirect  command  file  to  perform  this  operation  has  been
     included  in  the  installation  save set on this patch tape.  This
     file will restore the appropriate files to DSKP:[7,6,MON].  If  you
     wish  to use this command file, but are not using DSKP:[7,6,MON] as
     your distribution directory you will have to edit this command file
     to change the /RESTORE command to correspond to your directory.
        
        To use this command file, issue the following command:
        
        .R BACKUP
        /TAPE tape:
        /@DSKP:MON704.CCL[7,6]


     The following files must be in the common patching  area  when  the
     monitor is Autopatched:
        
        BUILDS.DCL      BUILDS.PTH      TOPS10.CCL      TOPS10.CMD

     It is expected that you will place a customized copy of  BUILDS.PTH
     in  PAT:.   Please  observe  the  following rules.  First, you MUST
     specify directories other then PAT:  for the  REL  (FGEN)  and  EXE
     (BUILD)  areas.   The  START.CTL procedure creates a START.MIC file
     which deletes all entries in these areas.  Second, you  should  use
     explicit  structures  and  PPNs when defining areas for FGEN, BUILD
     and BASE:.  Third, the distributed START.CTL will delete all  *.LOG
     files  in  BASE:.   A revised START.CTL with that command commented
     out can be found in the second  save-set  of  the  Autopatch  tape.
     Fourth,  you must include your definition of PAT:  and DIS:  in the
     definition of CTLS:  and  MON:.   Lastly,  invoking  START.CTL  and
     GEN.CTL  is  required  BEFORE you can select MONITOR-10 since F.MAC
     and  SYSCNF.MAC  are  created  by  GEN.   The  definition  of  PAT:
     specified  during  SELECT should match the definition in BUILDS.PTH
     to ensure accurate reporting by  PEP.   A  minimum  BUILDS.PTH  for
     building  a  monitor  can  be  found  in the second save-set of the
     Autopatch tape.

     The MPE and Customer Supported options to the TOPS-10  Monitor,  if
     used,  must  be  autopatched  before  the Control file to build the
     monitor is submitted.
                                                                 Page 30


     The Patch and Build control file for the re-build of  this  product
     as  well  as the Autopatch product description file are supplied in
     the Installation Save-set on the  Autopatch  tape.   See  the  last
     section  of  this  document  for a list of these files.  There is a
     BACKUP command file provided  in  the  first  Save-set  which  will
     restore  these  files  to  the  proper  directory.   See the README
     documentation file in the first Save-set for more information.
                                                                 Page 31


     3.13  PREPARING FOR AUTOPATCHING MPE-10

     You will need to copy the following file from the TOPS-10 MPE  7.04
     distribution  tape BB-X133C-SB into the disk directory you have set
     up as the MONITOR-10 distribution directory.
        
           From the first save set
        
                CPNSER.KEY
                CPNSER.MAC
                MPE.FIL

     An indirect  command  file  to  perform  this  operation  has  been
     included  in  the  installation  save set on this patch tape.  This
     file will restore the appropriate files to DSKP:[7,6,MON].  If  you
     wish  to use this command file, but are not using DSKP:[7,6,MON] as
     your distribution directory you will have to edit this command file
     to change the /RESTORE command to correspond to your directory.
        
        To use this command file, issue the following commands:
        
        .R BACKUP
        /TAPE tape:
        /@DSKP:MPE704.CCL[7,6]
        

     The Autopatch product description file for this product is supplied
     in  the  Installation Save-set on the Autopatch tape.  See the last
     section of this document for a listing of this file.   There  is  a
     BACKUP  command  file  provided  in  the  first Save-set which will
     restore  this  file  to  the  proper  directory.   See  the  README
     documentation file in the first Save-set for more information.
                                                                 Page 32


     3.14  PREPARING FOR AUTOPATCHING MS-SOURCES

     You will need to copy the following files  from  the  TOPS-10  7.04
     CUSP distribution tape BB-XXXXX-BB into the disk directory you have
     set up as the MS-SOURCES distribution directory.

        From the SFD [10,7,DECMAI,MS]
        
        MS.MAC          MSCNFG.MAC      MSDLVR.MAC      MSDSPL.MAC
        MSFIL.MAC       MSGUSR.MAC      MSHOST.MAC      MSLCL.MAC
        MSMCMD.MAC      MSNET.MAC       MSSEQ.MAC       MSTXT.MAC
        MSUNV.MAC       MSUTL.MAC       MSUUO.MAC       MSVER.MAC


     An indirect  command  file  to  perform  this  operation  has  been
     included  in  the  installation  save set on this patch tape.  This
     file will restore the appropriate files to DSKP:[7,6,MS].   If  you
     wish  to  use this command file, but are not using DSKP:[7,6,MS] as
     your distribution directory you will have to edit this command file
     to change the /RESTORE command to correspond to your directory.
        
        To use this command file, issue the following commands:
        
        .R BACKUP
        /TAPE tape:
        /@DSKP:MS1S11.CCL[7,6]


     Please note that the Autopatch process does  NOT  rebuild  MS  from
     sources.

     The Patch and Build control file for the update of this product  as
     well  as the Autopatch product description file are supplied in the
     Installation Save-set on the Autopatch tape.  See the last  section
     of  this  document  for  a  list of these files.  There is a BACKUP
     command file provided in the  first  Save-set  which  will  restore
     these  files to the proper directory.  See the README documentation
     file in the first Save-set for more information.
                                                                 Page 33


     3.15  PREPARING FOR AUTOPATCHING MX-SOURCES

     You will need to copy the following files from a CURRENT  Autopatch
     tape  into  the  disk  directory  you have set up as the MX-SOURCES
     distribution directory.
        
        From save-set MX V1A DISTRIBUTION
        
        CPYRYT.MAC      SENVAX.MAC      LISVAX.MAC      SMTSEN.MAC
        SMTLIS.MAC      MXNT10.MAC      MXUT10.MAC      NETTAB.MAC
        MXVER.MAC
        MXNLIB.R36      M10TYP.R36      MXPORT.R36      MXNSTR.R36
        MXNTLB.R36      MXDBUG.R36      MXNRSP.R36      MXNCOM.R36
        MXNCMI.R36      MXNRCH.R36      MXINI.R36       MXLIB.R36
        MXCNDT.R36      MXQMAN.R36      MXUFIL.R36      MXERR.R36
        MXLCL.R36       TBL.R36         MXNT10.R36      BLT.R36
        MONSYM.R36
        M10INT.B36      MXNMEM.B36      MXNQUE.B36      MXNTBL.B36
        MXNTXT.B36      MXDATA.B36      MXHOST.B36      MXLCL.B36
        MXQMAN.B36      MXUFIL.B36      TBL.B36         MXERR.B36
        MXDCNT.B36      MXNSKD.B36      MXNPAG.B36      NEWT10.B36
        M10IPC.B36      MXNNET.B36
        MX.REL
        MX10.CTL

     An indirect  command  file  to  perform  this  operation  has  been
     included  in  the  installation  save set on this patch tape.  This
     file will restore the appropriate files to DSKP:[7,6,CSP].  If  you
     wish  to use this command file, but are not using DSKP:[7,6,CSP] as
     your distribution directory you will have to edit this command file
     to change the /RESTORE command to correspond to your directory.
        
        To use this command file, issue the following commands:
        
        .R BACKUP
        /TAPE tape:
        /@DSKP:MX11AS.CCL[7,6]
        
     The following files are restored by this CCL but not Autopatched:

        MX.EXE          MX.MAP          README.MEM

     The Patch control file for the update of this product  as  well  as
     the   Autopatch  product  description  file  are  supplied  in  the
     Installation Save-set on the Autopatch tape.  See the last  section
     of  this  document  for  a  list of these files.  There is a BACKUP
     command file provided in the  first  Save-set  which  will  restore
     these  files to the proper directory.  See the README documentation
     file in the first
                                                                 Page 34


     3.16  PREPARING FOR AUTOPATCHING SORT-10

     Before preparing this product for Autopatching, you should  install
     the  product  on  your  system  as  described  in  the installation
     documentation supplied on the product  distribution  tape.   Unless
     the  product is correctly installed, you will not be able to SELECT
     it for Autopatching.

     The disk directory in which you have installed the executable files
     for  SORT-10  is referred to as the product installation directory.
     In most cases  this  will  be  [1,4]  or  one  of  the  directories
     belonging to SYS:.  This directory must contain the files:
        
                SORT.EXE
                FSORT.EXE

     The following files are required to build the SORT  product.   They
     must   be  available  either  in  the  patching  area  (PAT:),  the
     distribution area (DIS:), or in the installation area (INS:).

        From the first save-set of the Autopatch tape

        HELPER.REL      MACTEN.UNV      SCAN.REL        SCNMAC.UNV
        UUOSYM.UNV

     These files will be moved from the Autopatch tape when you use  one
     of the BACKUP CCL files described in the README file.

     You will  need  to  copy  the  following  files  from  the  SORT-10
     distribution  tape  BB-D489F-SB  or  from the COBOL-10 distribution
     tape into the disk  directory  you  have  set  up  as  the  SORT-10
     distribution directory.
        
           From save set SORT-SOURCE
        
        SORT.MAC        SRTFLT.MAC      SRTCBL.MAC      SRTPRM.MAC
        SRTCER.MAC      SRTSCN.MAC      SRTCMP.MAC      SRTSTA.MAC
        SRTUUO.MAC

     An indirect  command  file  to  perform  this  operation  has  been
     included  in  the  installation  save set on this patch tape.  This
     file will restore the appropriate files to DSKP:[7,6,SRT].  If  you
     wish  to use this command file, but are not using DSKP:[7,6,SRT] as
     your distribution directory you will have to edit this command file
     to change the /RESTORE command to correspond to your directory.
        
        To use this command file, issue the following commands:
        
        .R BACKUP
        /TAPE tape:
        /@DSKP:SRTV4D.CCL[7,6]
        
     This command file is valid for use  ONLY  with  the  separate  SORT
     distribution  tape.   Use  of the COBOL CCL file will load the SORT
     files from the COBOL distribution tape into DSKP:[7,6,SRT].
                                                                 Page 35


     The Patch and Build control file for the re-build of  this  product
     as  well  as the Autopatch product description file are supplied in
     the Installation Save-set on the  Autopatch  tape.   See  the  last
     section  of  this  document  for a list of these files.  There is a
     BACKUP command file provided  in  the  first  Save-set  which  will
     restore  these  files  to  the  proper  directory.   See the README
     documentation file in the first Save-set for more information.
                                                                 Page 36


     3.17  PREPARING FOR AUTOPATCHING UTILITIES-10

     Before preparing this product for Autopatching, you should  install
     the  product  on  your  system  as  described  in  the installation
     documentation supplied on the product  distribution  tape.   Unless
     the  product is correctly installed, you will not be able to SELECT
     it for Autopatching.

     The disk directory in which you have installed the executable files
     for  UTILITIES-10  is  referred  to  as  the  product  installation
     directory.  In most  cases  this  will  be  [1,4]  or  one  of  the
     directories  belonging  to  SYS:.   This directory must contain the
     files:
        ACTDAE.EXE      ACTLIB.REL      ACTPRM.UNV      ACTSYM.UNV
        BACKUP.EXE      BOOT.EXB        BOOT.EXE        BTDDT.EXE
        BTONCE.EXE      BTSPRM.UNV      COMPAR.EXE      COMPIL.EXE
        CREDIR.EXE      CREF.EXE        CRSCPY.EXE      CTHNRT.EXE
        D60JSY.REL      D60UNV.UNV      DAEMON.EXE      DDT.EXE
        DDT.REL         DDT11.EXE       DECLAR.EXE      DELFIL.EXE
        DIL.LIB         DIL.REL         DILV7.FOR       DITV7.FOR
        DIXV7.FOR       DIRECT.EXE      DSKLST.EXE      DSKRAT.EXE
        DTELDR.EXE      EDDT.REL        F11.EXE         FAL.EXE
        FE.EXE          FEFILE.EXE      FILCOM.EXE      FILDAE.EXE
        FILDDT.EXE      GLOB.EXE        HELP.EXE        HELPER.REL
        INITIA.EXE      JOBDAT.REL      JOBDAT.UNV      KDPLDR.EXE
        KSBOOT.EXE      KSONCE.EXE      LINK.EXE        LNK999.EXE
        LNKERR.EXE      LNKLOD.EXE      LNKMAP.EXE      LNKOV1.EXE
        LNKOV2.EXE      LNKSCN.EXE      LNKXIT.EXE      LOGIN.EXE
        LOGOUT.EXE      LP20.EXE        MACDLX.EXE      MACRO.EXE
        MACSYM.UNV      MACTEN.REL      MACTEN.UNV      MAKLIB.EXE
        MERGE.EXE       MIC.EXE         MONSYM.UNV      MS.EXE
        MX.EXE          NCPTAB.REL      NETLDR.EXE      NETWOR.EXE
        NFT.EXE         NOTIFY.EXE      OPSER.EXE       OVRLAY.REL
        PATH.EXE        PIP.EXE         PROJCT.EXE      QUOLST.EXE
        REACT.EXE       RMS.EXE         RMS.REL         RMSCOB.EXE
        RMSINI.REL      RMSINT.R36      RMSINT.UNV      RMSSYM.LUS
        RMSUTL.EXE      RSXT10.EXE      RUNOFF.EXE      SCAN.REL
        SCOMM.EXE       SCDSET.EXE      SCNMAC.UNV      SETSRC.EXE
        SMFILE.EXE      SPEAR.EXE       SPRCOM.EXE      SPRINS.EXE
        SPRKLE.EXE      SPRRET.EXE      SPRSUM.EXE      SWIL.REL
        SWIL.UNV        SYSANS.EXE      SYSDLT.EXE      SYSDPA.EXE
        SYSDPB.EXE      SYSDPY.EXE      SYSHZL.EXE      SYSTAT.EXE
        SYSV50.EXE      SYSV52.EXE      SYSV61.EXE      SYSVBX.EXE
        T10KL.RAM       TECO.EXE        TGHA.EXE        UFDSET.REL
        UFDPRM.UNV      UPDATE.EXE      UUOSYM.REL      UUOSYM.UNV
        VMDDT.EXE       WILD.REL

     You will need to copy the following files from the  TOPS  10  V7.04
     CUSP   BB-FP63B-SB/BB-X128C-SB  distribution  tape  into  the  disk
     directory  you  have  set  up  as  the  UTILITIES-10   distribution
     directory.
        ACTCUS.MAC      ACTDAE.MAC      ACTLIB.MAC      ACTRCD.MAC
        ACTSYM.MAC      BACKRS.MAC      BACKUP.MAC      BOOT.MAC
        CTHNRT.MAC      COMPAR.MAC      COMPIL.MAC      CREDIR.MAC
        CREF.MAC        CRSCPY.MAC      D60JSY.MAC      D60UNV.MAC
                                                                 Page 37


        DAEMON.MAC      DDT.MAC         DDT11.MAC       DDTFIL.MAC
        DDTGP.MAC       DDTSIM.MAC      DDTSYM.MAC      DECLAR.MAC
        DELFIL.MAC      DIRECT.MAC      DSKLST.MAC      DSKRAT.MAC
        DTELDR.MAC      DXMCA.ADX       DXMCD.ADX       DXMPA.A8
        ENDECR.MAC      F11.MAC         F1EDDT.MAC      F1FDDT.MAC
        F1UDDT.MAC      F1VDDT.MAC      FAL.MAC         FE.MAC
        FEFILE.MAC      FILCOM.MAC      FILDAE.MAC      GCOM.MAC
        GKBD.MAC        GLOB.MAC        GMAC.MAC        GSCN.MAC
        HELP.MAC        HELPER.MAC      INITIA.MAC      INTCUS.MAC
        INTPRM.MAC      JOBDAT.MAC      KDPLDR.MAC      LNK999.MAC
        LNKCOR.MAC      LNKCST.MAC      LNKD10.MAC      LNKERR.MAC
        LNKEXO.MAC      LNKFI0.MAC      LNKHSH.MAC      LNKHST.MAC
        LNKINI.MAC      LNKLOD.MAC      LNKLOG.MAC      LNKLOW.MAC
        LNKMAP.MAC      LNKNEW.MAC      LNKOLD.MAC      LNKOV1.MAC
        LNKOV2.MAC      LNKOVS.MAC      LNKPAR.MAC      LNKPLT.MAC
        LNKSCN.MAC      LNKSUB.MAC      LNKT10.MAC      LNKWLD.MAC
        LNKXIT.MAC      LOGIN.MAC       LP20.MAC        MACRO.MAC
        MACSYM.MAC      MACTEN.MAC      MAKLIB.MAC      MERGE.MAC
        MIC.MAC         MONSYM.MAC      NCPTAB.MAC      NETLDR.MAC
        NETWOR.MAC      NIP.MAC         NFT.MAC         OPSER.MAC
        OVRLAY.MAC      OVRPAR.MAC      PARSE.MAC       PATH.MAC
        PIP.MAC         PLTDCL.MAC      PLTGLB.MAC      PLTIO.MAC
        PLTMTH.MAC      PLTPRM.MAC      PLTUTL.MAC      PROJCT.MAC
        PRS.MAC         QUOLST.MAC      REACT.MAC       RSXCMN.MAC
        RSXT10.MAC      RSXTTL.MAC      RUNOFF.MAC      SCAN.MAC
        SCDEXE.MAC      SCDSET.FOR      SCNMAC.MAC      SETSRC.MAC
        SMFILE.MAC      SMPREB.MAC      SWIL.MAC        SWIERM.MAC
        SWIFIL.MAC      SWIHLP.MAC      SWILIO.MAC      SWIMEM.MAC
        SWIMSC.MAC      SWINET.MAC      SWIQUE.MAC      SWISCN.MAC
        SWITOU.MAC      SWIWLD.MAC      SYSDPU.MAC      SYSDPY.MAC
        SYSTAT.MAC      TECO.MAC        TSC.MAC         UFDSET.MAC
        UPDATE.MAC      USGSUB.MAC      UUOSYM.MAC      WILD.MAC

     An indirect  command  file  to  perform  this  operation  has  been
     included  in  the  installation  save set on this patch tape.  This
     file will restore the appropriate files to DSKP:[7,6,CSP].  If  you
     wish  to use this command file, but are not using DSKP:[7,6,CSP] as
     your distribution directory you will have to edit this command file
     to change the /RESTORE command to correspond to your directory.

     An indirect command file which restores  all  autopatched  products
     from the CUSP tape has also been provided.
        
        To use this command file, issue the following commands:
        
        .R BACKUP
        /TAPE tape:
        /@DSKP:CSP704.CCL[7,6]
        

     The following files are required to build  the  UTILITIES  product.
     They  must  be  available  either  in the patching area (PAT:), the
     distribution area (DIS:), or in the installation area (INS:).

        From the first save-set of the Autopatch tape
                                                                 Page 38



        B361LB.REL      OPRPAR.REL

     These file will be moved from the Autopatch tape when you  use  one
     of the BACKUP CCL files described in the README file.

     When selecting the UTILITIES-10 product for Autopatching you should
     include  the  DIS:  for MONITOR as part of your path definition for
     DIS:     for    the    UTILITIES-10    product.     For    example,
     DSKP:[7,6,CSP],DSKP:[7,6,MON].

     The Patch and Build control file for the re-build of  this  product
     as  well  as the Autopatch product description file are supplied in
     the Installation Save-set on the  Autopatch  tape.   See  the  last
     section  of  this  document  for a list of these files.  There is a
     BACKUP command file provided  in  the  first  Save-set  which  will
     restore  these  files  to  the  proper  directory.   See the README
     documentation file in the first Save-set for more information.
                                                                 Page 39


     4.0  CONTENTS OF INSTALLATION SAVE SET


        File            Description
        ----            -----------
        PEP.EXE         Patch Exec Program
        PEPB.EXE        Patch Exec for BATCH
        PEP.HLP         PEP Help file
        PEP101.PDF      TOPS-10 Product Description Master file

        DCRYPT.EXE      Unsupported Decryption tool
        DCRYPT.HLP      Help file for DECRYPT

        INSTAL.DOC      Installation Documentation for Autopatch 10/20
        AUTINS.DIR      Checksummed directory of the Autopatch
                           Installation Area

                *ALGOL-10*
        ALG10B.CTL      patch and build control file
        ALG10B.PDF      product description file
        ALG10B.CCL      command file for preparing distribution area

                *ANF10*
        ANF704.CTL      patch and build control file
        ANF704.PDF      product description file
        ANF704.CCL      command file for preparing distribution area

                *APLSF-10*
        APL1S2.CTL      patch and build control file
        APL1S2.PDF      product description file
        APL1S2.CCL      command file for preparing distribution area

                *COBOL-10*
        CBL12C.CTL      patch and build control file
        CBL12C.PDF      product description file
        CBL12C.CCL      command file for preparing distribution area

                *COBOL-REP*
        CBR12C.CTL      patch and build control file
        CBR12C.PDF      product description file
        CBR12C.CCL      command file for preparing distribution area

                *CUSTOMER-SUPPORTED*
        CUS704.CTL      patch and build control file
        CUS704.PDF      product description file
        CUS704.CCL      command file for preparing distribution area

                *DBMS-10*
        DBMV5A.CTL      patch and build control file
        DBMV5A.PDF      product description file
        DBMV5A.CCL      command file for preparing DBMS-10 distribution area

                *DECNET*
        DEC704.CTL      patch and build control file
        DEC704.PDF      product description file
                                                                 Page 40


        DEC704.CCL      command file for preparing distribution area

                *FORTRAN-10*
        FTN111.CTL      patch and build control file
        FTN111.PDF      product description file
        FTN111.CCL      command file for preparing distribution area
        DBCS1F.CMD      command file for building DBMSF


                *FORTRAN-REP*
        FTN1X1.CTL      patch and build control file
        FTN1X1.PDF      product description file
        FTN1X1.CCL      command file for preparing distribution area
        DBCS1F.CMD      command file for building DBMSF

                *GALAXY-10*
        GAL704.CTL      patch and build control file
        GAL704.PDF      product description file
        GAL704.CCL      command file for preparing distribution area
        CNFHDW.MAC      New GALAXY Source file
        BATCON.CTL      Build control files
        CDRIVE.CTL
        GALGEN.CTL
        LPTSPL.CTL
        MOUNT.CTL
        OPERAT.CTL
        PLEASE.CTL
        PULSAR.CTL
        QUASAR.CTL
        QUEUE.CTL
        SPRINT.CTL

                *IBMCOM-10-ET*
        IETV04.CTL      patch and build control file
        IETV04.PDF      product description file
        IETV04.CCL      command file for preparing distribution area
        MACRO.P11       renmamed copy of MACROS.P11

                *IBMCOM-10-HASP*
        IHSV01.CTL      patch and build control file
        IHSV01.PDF      product description file
        IHSV01.CCL      command file for preparing distribution area
        MACRO.P11       renmamed copy of MACROS.P11

                *MCB-10*
        MCB704.CTL      patch and build control file
        MCB704.PDF      product description file
        MCB704.CCL      command file for preparing distribution area

                *MONITOR-10*
        MON704.CTL      patch and build control file
        MON704.PDF      product description file
        MON704.CCL      command file for preparing distribution area

                *MPE*
                                                                 Page 41


        MPE704.CTL      patch and build control file
        MPE704.PDF      product description file
        MPE704.CCL      command file for preparing distribution area

                *MS-SOURCES*
        MS1S11.CTL      patch control file
        MS1S11.PDF      product description file
        MS1S11.CCL      command file for preparing distribution area

                *MX-SOURCES*
        MX11AS.CTL      patch control file
        MX11AS.PDF      product description file
        MX11AS.CCL      command file for preparing distribution area

                *SORT-10*
        SRTV4D.CTL      patch and build control file
        SRTV4D.PDF      product description file
        SRTV4D.CCL      command file for preparing distribution area
                                from SORT distribution

                *UTILITIES-10*
        UTL704.CTL      patch and build control file
        UTL704.PDF      product description file
        CSP704.CCL      command file for preparing distribution area
        DXMCA.ADX       Microcode files for BOOT
        DXMCD.ADX
        DXMPA.A8
        C1DLNK.CMD      Revised files for LINK
        C1DOVL.CMD
        C1PLNK.CMD
        C1POVL.CMD
        L1DLNK.CCL
        LIPLNK.CCL
        LNK999.CCL
        LNKERR.CCL
        LNKINI.CCL
        LNKLOD.CCL
        LNKMAP.CCL
        LNKOV1.CCL
        LNKOV2.CCL
        LNKSCN.CCL
        LNKXIT.CCL