Google
 

Trailing-Edge - PDP-10 Archives - bb-bt99h-bb - readme.014
There is 1 other file named readme.014 in the archive. Click here to see a list.


1.0  INTRODUCTION

This  is  the  fourteenth  Autopatch  set.   It  contains  patches   for
ALGOL-10-V1-2,   ANF10-V703,   APL-10-V2,   APLSF-10-V2,  COBOL-10-V12C,
CUSTOMER-SUPPORTED-10-V703,       DECNET-10-V703,        FORTRAN-10-V10,
IBMCOM-10-ET-V4,    IBMCOM-10-HASP-V1,   MONITOR-10-V703,   MPE-10-V703,
SORT-10-V4D, and UTILITIES-10-V703.  To install Autopatch for the  first
time,  you  must  first  restore  the  second  save  set  and follow the
instructions found in the Autopatch Procedures/Reference Manual and  the
INSTAL.DOC  file.   Information  specific to each product is recorded in
section 5.0 of this document.



2.0  EXCEPTIONS


     1.  ANF10-V703,     CUSTOMER-SUPPORTED-10-V703,     DECNET-10-V703,
         MONITOR-10-V703,   MPE-10-V703,   and   UTILITIES-10-V703   are
         autopatched for the first time with this tape.

     2.  The following product(s) are no longer Autopatched  because  of
         new         releases:          ANF10-V23,        COBOL-10-V12B,
         DECNET-10-UTILITIES-V702,     FORTRAN-10-V6,     FORTRAN-10-V7,
         GALAXY-10-V4-1,   GALAXY-10-V702,   LINK-10-V5-1,  MCB-10-V702,
         MPE-10-V702,  MS-10-V10,  NFT-10-V1,  RMS-10-V1,   SORT-10-V4C,
         TOPS-10-DN6X-V701A,     TOPS-10-KI-V701A,     TOPS-10-KL-V701A,
         TOPS-10-KL-V702,       TOPS-10-KS-V701A,       TOPS-10-KS-V702,
         TOPS-10-MPE-V701A,  TOPS-10-TSK-V701,  UTILITIES-10-V701A,  and
         UTILITIES-10-V702.

         *NOTE* It is strongly suggested that you DESELECT any of  these
         products   before  proceeding  with  processing  any  currently
         supported products.

     3.  The following Autopatched product(s) do not have any new  edits
         delivered  with  this  patch  set:   ALGOL-10-V10B,  APL-10-V2,
         APLSF-10-V2, DBMS-10-V5A, and SORT-20-V4D.

     4.  (*new*)  The  following  files  must  be  in  PAT:   when   the
         MONITOR-10 product is built:

                BUILDS.DCL      BUILDS.PTH

     5.  (*new*) The ANF10 product is NOT  rebuilt  by  Autopatch.   The
         Autopatch process will update the supported sources in the DIS:
         area.  After the INSTALL command has been  processed,  you  may
         use the sources in DIS:  to rebuild the product with procedures
         which are appropriate for your site.

         Also, there are 11 .P11 files that were omitted  from  the  ANF
         distribution.   These  files  have  been included on the second
         save-set of this Autopatch tape.  You must restore these  files
         to  the  DIS:   area for ANF10 before ANF10 can be selected for
         Autopatching.  Use of  either  ANF703.A14  or  ANF703.P14  will
                                                                  Page 2


         attempt to restore thes files to DSKP:[7,6,ANF].

     6.  (*new*) This tape contains PEP at edit level 161.  This version
         is  required in order to update the DECNET-10 product.  Be sure
         that PEP.EXE and PEPB.EXE are restored to SYS:.

     7.  (*new*) The MONITOR-10-V703 build process is designed to be  as
         close as possible to the standard monitor build procedure.  One
         set of sources is maintained from which any flavor or  multiple
         monitors  can be built.  However, Autopatch will track and move
         only one monitor.

         You must include a path definition for PAT:  in the  BUILDS.PTH
         file for proper operation of Autopatch.  You must also have the
         files created by START.CTL and GEN.CTL in the PAT:  area before
         selecting the MONITOR-10 product.

         If your monitor is to include DECNET support, then  you  should
         define DIS:  when selecting the MONITOR-10 product to be a path
         which includes the DIS:  area for the DECNET-10  product.   For
         instance, DSKP:[7,6,MON],DSKP:[7,6,DECNET].

     8.  (*new*) The UTILITIES-10 product  now  includes  virtually  all
         products  found  on  the  CUSP  tape.   This  includes 11-based
         products.  All output files must  be  'seen'  in  INS:   before
         UTILITIES-10  can  be selected.  This includes components which
         don't normally reside in SYS:  such as BOOT.EXB and BOOTML.EXB.
         Be sure to read the UTILITIES-10 section of the INSTAL.DOC file
         in the second save-set for a complete list of files  that  must
         be intially found in INS:.

     9.  (*new*) The  version  of  SOUP  for  Autopatch  (SOUPR)  has  a
         filename  which conflicts with the original and still supported
         SOUP product.  The  name  of  the  SOUPR  file  in  the  second
         save-set has been changed from COMPAR.MAC to COMPR.MAC.

         If the COMPAR.MAC file has been  previously  restored  to  PAT:
         then  it  must  be deleted or the selection of UTLITIES-10-V703
         will report a checksum mismatch and the wrong  COMPAR.REL  file
         will be created.

    10.  (*new*) There are three Patch Command Files on  this  save-set.
         They   are   APL1B2.MKL,  APL1S2.MKL,  and  DBMV5A.MKL.   These
         products have no patches on this tape.  Without these files, if
         you  were  to  'AUTOPATCH' the products with PEP and SUBmit the
         patch and  build  control  files  the  process  would  use  old
         patching  indirect  command  files.  This would cause a failure
         with DBMS.  The 'null' patching  indirect  command  files  will
         avoid  this  problem.   Any  checksum  warnings regarding these
         files may be ignored.

    11.  (tape 11) The Autopatch build for source-patched products  will
         delete  source files in PAT:  to prevent problems if a build is
         re-started.  This process may fail if  PAT:   is  defined  with
         SFDs.   Either  do not use SFDs when defining PAT:  or manually
                                                                  Page 3


         delete the source files  in  the  SFD  before  re-starting  the
         Autopatch build.

    12.  (tape 11) If you are using the new FORTRAN-10 V10 with DBMS you
         will need a revised DBCS1F.CMD file from the second save-set on
         the Autopatch tape.   This  file  should  be  copied  into  the
         FORTRAN  distribution  area.   The  copy of this file which was
         distributed with DBMS V5A must be removed or the FORTRAN  build
         will fail.

    13.  (tape 11) A revised copy of TGHA.EXE is contained in the  first
         save-set  on  this  tape.  This copy is required for use of the
         new MG20 memory.

    14.  (tape 10) If you are using DBMS with FORTRAN or COBOL,  do  not
         INSTALL  DBMS  with  PEP  until  FORTRAN  and/or COBOL has been
         built.  A feature of PEP which was new with tape 9 deletes  the
         autopatched files from PAT:  upon successful installation.  The
         COBOL and FORTRAN products depend on the necessary  DBMS  files
         being in PAT:.

    15.  (tape 10) There are three .REL modules for DBMS  (FML10,  INF10
         and MND10) which are null.  This causes a %CGV error message at
         the end of the batch job and when PEP is checking  the  results
         of the batch job.  These messages should be ignored.

    16.  (tape 9) There are two new features of PEP and PEPB  which  are
         worthy  of  note.  First, the new PEP will automatically delete
         copies of files in PAT:  which have been successfully installed
         with the INSTALL command.

         Second,  the  definition  of  ASL:   has  been  changed  to  be
         PAT:,DIS:,INS:.        The       old       definition       was
         PAT:,DIS:,REL:,UNV:,SYS:.   This  change  was  made  to  obtain
         better  control  over  all files used in the build process.  We
         have delivered what we believe to be a  complete  set  of  base
         building software on the Autopatch tape.  If your procedure has
         problems you may have to copy certain files into PAT:, DIS:, or
         INS:.

         The following files are required for Autopatch use, not put  in
         place by Autopatch, and may have been previously found in SYS:.

                        IBMCOM HASP and ET

                DDT11.EXE       GALCNF.UNV      MACDLX.EXE

                        FORTRAN

                BLIS10.EXE      BLIS10.ERR

         If these files are currently found in SYS:  they must be copied
         or moved to PAT:, DIS:, or INS:.

         The SORT product currently looks for FTDEFS.UNV amd  METUNV.UNV
                                                                  Page 4


         in  ASL:.   In  fact  the  SORT build does NOT use these files.
         This will be fixed on a future Autopatch tape.  Since SYS:   is
         no  longer  in the ASL:  definition, you may have to copy these
         files from SYS:.  Users who Autopatch SORT for the  first  time
         and  users  who have these files in PAT:  from a previous COBOL
         build will not have this problem.

    17.  (tape 9) The IBMCOM products have  a  module  named  MACROS.P11
         which  conflicts  with a module by the same name with different
         contents in the ANF10 product.  The IBMCOM  MACROS  module  has
         been  renamed  as  MACRO.P11.   For  users  of Autopatch on the
         IBMCOM products for the first time, if  the  IETV04  or  IHSV01
         .CCL  file  is  used to load the distribution directory then no
         action is required by the  user.   Otherwise,  the  distributed
         MACROS.P11  file  must  be  renamed  to  be  MACRO.P11  or  the
         MACRO.P11 file on the Autopatch tape must be put in DIS:.   The
         UTILTY.UPD file will update the Patch Database file.

    18.  (tape 7) Changes have been made to  the  PEP  utility.   It  is
         MANDATORY  that  PEP.EXE and PEPB.EXE be restored to SYS:  from
         the installation (second) save-set.

         Due to a limited amount of space  in  some  of  PEP's  internal
         tables,  we  are  now declaring some products to be "obsolete".
         These products will be removed from PEP's internal tables.  For
         the  most  part  this process is transparent to you, unless the
         obsolete  product  has  previously  been   SELECTed.    Suppose
         FORTRAN-10-V6  is one of your SELECTed products.  In that case,
         the following message would be displayed the first time you run
         the new PEP:

             [FORTRAN-10-V6 is now obsolete.
              Edits are no longer being delivered.
              You should DESELECT this product.]

         This message  will  only  appear  ONCE  PER  SELECTED  OBSOLETE
         PRODUCT.   Use  the  DESELECT  command  to  purge  the obsolete
         product from your database.


                                      NOTE

             The PEP101.PDF file  is  NOT  compatible  with  earlier
             versions of PEP.



         There is now a short version of the INFORMATION command  called
         STATUS.   It  displays  the status information and logical name
         definitions, but does not list any files  or  their  checksums.
         For example, you might see the following:

             PEP>status LINK-10-V5-1

             LINK-10-V5-1 is ready to be SETUP for patch and rebuild
                                                                  Page 5


              Patches retrieved through patch tape 7

              Logical names:
                PAT: (autopatching directory) defined as DSKP:[7,6]
                DIS: (distribution directory) defined as DSKP:[7,6,LINK]
                BAK: (backup directory) defined as DSKP:[7,6,BACKUP]
                INS: (installation directory) defined as SYS:
                ASL: (autopatch search list) defined as PAT:,DIS:,INS:


    19.  (tape 7) Edit 612 to DBMS-10-V5A eliminates the  need  for  the
         DBSINF.REL  module  which  was  introduced on Autopatch tape 5.
         Users who have Autopatched DBMS previously are urged to be sure
         that  the  new  version of the DBINF1.CMD file is restored from
         the patch set 7 save set on this tape.  Use of  the  DBMV5A.Ann
         file will accomplish this task.

    20.  (tape 7) The second chapter of  the  TOPS-10/TOPS-20  Autopatch
         Procedures/Reference  Manual  suggests a quota of 20,000 blocks
         for the [7,6] PPN on page 2-2.  Because of  additional  product
         support, it is now suggested that you use a figure of 140000.

    21.  (tape  6)  The  patch  directory   files   (.DPD)   have   been
         re-formatted;   the  same  number of edits, but less 'patches',
         are  described.   Also,  intermediate  checkpointing  has  been
         suppressed during the execution of the PEP 'AUTOPATCH' command.
         Checkpoint processing  time  has  been  SIGNIFICANTLY  reduced.
         These  changes  will  improve  PEP  performance, but will cause
         minor variations from the examples provided on pages 2-7,  2-17
         and 3-8 of the Autopatch Procedures/Reference Manual.

    22.  (tape 6) Users of FORTRAN with DBMS MUST create a file  -  read
         the INSTAL.DOC file.

         If  you  have  previously  SELECTed  DBMS  for  Autopatch   and
         indicated  that FORTRAN was being used than you may want to 're
         do' DBMS.  FORTRAN V6 is  no  longer  supported  by  Autopatch.
         With  FORTRAN  V7 and later the FORLIB.REL file is not modified
         for DBMS and the DBMSF.EXE file is autopatched by FORTRAN.

         The suggested procedure  is  to  use  the  DBMV5A.Ann  file  to
         restore  all  files  for  DBMS  from  this  tape  and issue the
         DESELECT and SELECT commands  for  DBMS-10-V5A  to  PEP  before
         Autopatching  DBMS.  Otherwise, the DBMS Autopatch process will
         'install' copies of FORLIB.REL and DBMSF.EXE which is also done
         by the FORTRAN Autopatch process.

    23.  (tape 6) There are  three  warning  messages  seen  during  the
         patching of REL libraries of the DBMS product.  Newer edits are
         trying to remove edits which were suppressed.   This  condition
         is non-fatal and has no impact on the success of DBMS updating.
         Ignore the messages.

    24.  (tape 6) BATCH time limits for FORTRAN and COBOL should be high
         to ensure that the product build BATCH jobs do not abort due to
                                                                  Page 6


         CPU time overrun.  Use  a  figure  of  5  hours  to  cover  all
         possibilities.

    25.  (tape 6) Some products can optionally use other products.  This
         means  that  one  product  may  have  to be patched and rebuilt
         before another product.  For example, COBOL can optionally  use
         the  DBMS  product.   The COBOL Autopatch process requires that
         DBMS and SORT be updated before COBOL.  In order to  apply  all
         patches  correctly  you must SUBMIT the Patch and Build Control
         file for SORT and DBMS before the COBOL Control file.  The MPE,
         Customer-supported  and  Decnet  options to the TOPS-10 Monitor
         must be Autopatched  before  the  Control  file  to  build  the
         monitor is submitted.

    26.  (tape 5) Before selecting the ALGOL product for Autopatching be
         sure  to  read  the  note  in  the  INSTAL.DOC file regarding a
         required rename of the OTS.

    27.  (tape 4) When PEP is run, the default directory must be PAT:.

    28.  (tape 4) It is advised that all desired  products  be  SELECTed
         for  Autopatching  before  entering  the  AUTOPATCH or RETRIEVE
         command for the first time.  The patch retrieval process is NOT
         product  specific.   This  process  can  be  invoked  with  the
         RETRIEVE command or the AUTOPATCH command.  PEP will then  read
         the  entire  patch  directory  file (.DPD) and update the patch
         database  file  (.PDB)  for  all  SELECTed  products.   If  the
         AUTOPATCH  command  is entered for a product which was SELECTed
         at the time of a prior retrieval process, a statement  will  be
         made indicating that all patches have already been retrieved.




3.0  RELATED DOCUMENTS

TOPS-10/TOPS-20 Autopatch Procedures/Reference Manual (AA-H729A-TK)
INSTAL.DOC      (in Installation Save Set on this tape)



4.0  FILE INDEX

Patch Set 014

File            Description

README.014      Patch Set 014 Master Documentation File
TAP014.DIR      Directory with Checksums of Patch Set 014
PAT114.DPD      Patch Directory File for Patch Set 014
APL1B2.MKL      Null Patch Command Files
APL1S2.MKL
DBMV5A.MKL
APEDIT.RPT      Autopatch Edit Report
UTILTY.UPD      Utility checksum and version update file
                                                                  Page 7



Edit Description Files

ANF703.D14      ANF10-V703                      Edit Description File
CBL12C.D14      COBOL-10-V12C                   Edit Description File
FTN10.D14       FORTRAN-10-V10                  Edit Description File
IETV04.D14      IBMCOM-10-ET-V4                 Edit Description File
IHSV01.D14      IBMCOM-10-HASP-V1               Edit Description File
MON703.D14      MONITOR-10-V703                 Edit Description File
UTL703.D14      UTILITIES-10-V703               Edit Description File

Patch Files

CBLIO.C14       CBLIO .MAC Patch File   COBOL-10-V12C
CLEANC.C14      CLEANC.MAC
CMNGEN.C14      CMNGEN.MAC
COBOLC.C14      COBOLC.MAC
COBST.C14       COBST .MAC
COBVER.C14      COBVER.MAC
CPYLIB.C14      CPYLIB.MAC
CTREE.C14       CTREE .MAC
GETITM.C14      GETITM.MAC
IMPURE.C14      IMPURE.MAC
ISAM.C14        ISAM  .MAC
LIBARY.C14      LIBARY.MAC
MOVGEN.C14      MOVGEN.MAC
MSCGEN.C14      MSCGEN.MAC
PSCAN.C14       PSCAN .MAC
SETRET.C14      SETRET.MAC
SRTGEN.C14      SRTGEN.MAC
TABLES.C14      TABLES.MAC
XPAND.C14       XPAND .MAC

                                                                  Page 8


ACT1.C14        ACT1  .BLI Patch File   FORTRAN-10-V10
ARRXPN.C14      ARRXPN.BLI
CGDO.C14        CGDO  .BLI
COMSUB.C14      COMSUB.BLI
DEFPT.C14       DEFPT .BLI
EXPRES.C14      EXPRES.BLI
FORDDT.C14      FORDDT.MAC
FORFMT.C14      FORFMT.MAC
FORHST.C14      FORHST.MAC
FORMSG.C14      FORMSG.MAC
FOROPN.C14      FOROPN.MAC
FORPRM.C14      FORPRM.MAC
FORSRT.C14      FORSRT.MAC
LEXICA.C14      LEXICA.BLI
MTHDBL.C14      MTHDBL.MAC
MTHGDB.C14      MTHGDB.MAC
MTHHST.C14      MTHHST.MAC
OUTMOD.C14      OUTMOD.BLI
REGAL2.C14      REGAL2.BLI
REVHST.C14      REVHST.MAC
STA0.C14        STA0  .BLI
STA1.C14        STA1  .BLI
STA3.C14        STA3  .BLI

DORTB.X14       DORTB .EXE Patch File   FORTRAN-REP-V10
DORTC.X14       DORTC .EXE
DORTD.X14       DORTD .EXE
DORTE.X14       DORTE .EXE
DORTF.X14       DORTF .EXE
DORTG.X14       DORTG .EXE
DORTRA.X14      DORTRA.EXE
FORDDT.X14      FORDDT.REL
FORLIB.X14      FORLIB.REL
FORO10.X14      FORO10.EXE
FORTB.X14       FORTB .EXE
FORTC.X14       FORTC .EXE
FORTD.X14       FORTD .EXE
FORTE.X14       FORTE .EXE
FORTF.X14       FORTF .EXE
FORTG.X14       FORTG .EXE
FORTRA.X14      FORTRA.EXE
SINGLE.X14      SINGLE.EXE

D60SPD.C14      D60SPD.MAC Patch File   IBMCOM-10-ET-V4/
HBSC.C14        HBSC  .P11              IBMCOM-10-HASP-V1
IBMPAT.C14      IBMPAT.MAC
IBMSPL.C14      IBMSPL.MAC
STGMAN.C14      STGMAN.MAC
XL3780.C14      XL3780.MAC

                                                                  Page 9


CLOCK1.C14      CLOCK1.MAC Patch File   MONITOR-10-V703
COMMON.C14      COMMON.MAC
DLPSER.C14      DLPSER.MAC
FILIO.C14       FILIO .MAC
FILUUO.C14      FILUUO.MAC
IPCSER.C14      IPCSER.MAC
LP2SER.C14      LP2SER.MAC
LPTSER.C14      LPTSER.MAC
PTYSER.C14      PTYSER.MAC
S.C14           S     .MAC
SCNSER.C14      SCNSER.MAC
TAPUUO.C14      TAPUUO.MAC
VMSER.C14       VMSER .MAC

BACKUP.C14      BACKUP.MAC Patch File   UTILITIES-10-V703
INITIA.C14      INITIA.MAC
LOGIN.C14       LOGIN .MAC
SYSTAT.C14      SYSTAT.MAC

Base Building Software

ACTSYM.UNV      MACRO.EXE
COMPIL.EXE      MACSYM.UNV
CREF.EXE        MACTEN.UNV
D60JSY.MAC      MAKLIB.EXE
D60JSY.REL      NCPTAB.REL
D60UNV.MAC      ORNMAC.UNV
D60UNV.UNV      OVRLAY.REL
DIRECT.EXE      PIP.EXE
EDDT.REL        QSRMAC.UNV
FORDBM.REL      SCAN.REL
GLOB.EXE        SCNMAC.UNV
GLXLIB.REL      TECO.EXE
GLXMAC.UNV      UFDPRM.UNV
HELPER.REL      UFDSET.REL
JOBDAT.REL      UUOSYM.UNV
JOBDAT.UNV      WILD.REL
LINK.EXE
LNK999.EXE
LNKERR.EXE
LNKLOD.EXE
LNKMAP.EXE
LNKOV1.EXE
LNKOV2.EXE
LNKSCN.EXE
LNKXIT.EXE

                                                                 Page 10


Patch BACKUP Command Files

ANF703.P14      Restores files from Patch Set #014 for ANF10-V703
CBL12C.P14      Restores files from Patch Set #014 for COBOL-10-V12C
CBR12C.P14      Restores files from Patch Set #014 for COBOL-REP-V12C
CUS703.P14      Restores files from Patch Set #014 for CUSTOMER-SUPPORTED-10-V703
DEC703.P14      Restores files from Patch Set #014 for DECNET-10-V703
FTN10.P14       Restores files from Patch Set #014 for FORTRAN-10-V10
FTN10R.P14      Restores files from Patch Set #014 for FORTRAN-REP-V10
IETV04.P14      Restores files from Patch Set #014 for IBMCOM-10-ET-V4
IHSV01.P14      Restores files from Patch Set #014 for IBMCOM-10-HASP-V1
MON703.P14      Restores files from Patch Set #014 for MONITOR-10-V703
MPE703.P14      Restores files from Patch Set #014 for MPE-10-V703
UTL703.P14      Restores files from Patch Set #014 for UTILITIES-10-V703

ALG10B.A14      Restores files from ALL Patch Sets for ALGOL-10-V10B
ANF703.A14      Restores files from ALL Patch Sets for ANF10-V703
APL1B2.A14      Restores files from ALL Patch Sets for APL-10-V2
APL1S2.A14      Restores files from ALL Patch Sets for APLSF-10-V2
CBL12C.A14      Restores files from ALL Patch Sets for COBOL-10-V12C
CBR12C.A14      Restores files from ALL Patch Sets for COBOL-REP-V12C
CUS703.A14      Restores files from ALL Patch Sets for CUSTOMER-SUPPORTED-10-V703
DBMV5A.A14      Restores files from ALL Patch Sets for DBMS-10-V5A
DEC703.A14      Restores files from ALL Patch Sets for DECNET-10-V703
FTN10.A14       Restores files from ALL Patch Sets for FORTRAN-10-V10
FTN10R.A14      Restores files from ALL Patch Sets for FORTRAN-REP-V10
IETV04.A14      Restores files from ALL Patch Sets for IBMCOM-10-ET-V4
IHSV01.A14      Restores files from ALL Patch Sets for IBMCOM-10-HASP-V1
MON703.A14      Restores files from ALL Patch Sets for MONITOR-10-V703
MPE703.A14      Restores files from ALL Patch Sets for MPE-10-V703
SRTV4D.A14      Restores files from ALL Patch Sets for SORT-10-V4D
UTL703.A14      Restores files from ALL Patch Sets for UTILITIES-10-V703




5.0  PRODUCT DOCUMENTATION

                                                                 Page 11


ALGOL-10-V10B           Product Information             PRODUCT CODE:
                          Patch Set 014                 ALG10B

This patch set does not provide any edits for ALGOL-10-V10B.

If you are patching the product for the first time, you  must  define  a
distribution   area   and  obtain  some  files  from  the  ALGOL-10-V10B
distribution tape.  This process is described in the INSTAL.DOC file  in
the   second   save   set   on   this   tape   and   in   the  Autopatch
Procedures/Reference Manual.  The ALG10B.CCL Distribution BACKUP Command
file  found  in  the Installation Save Set may be used for this purpose.
If using Autopatch for the first time on this product you  may  use  the
ALG10B.A14  Patch  BACKUP  Command  file to restore files from all Patch
Sets.
                                                                 Page 12


ANF10-V703              Product Information             PRODUCT CODE:
                          Patch Set 014                 ANF703

This patch set provides the required files to update ANF10-V703 to  edit
level 999.

If you are patching the product for the first time, you  must  define  a
distribution  area  and obtain some files from the TOPS-10 V7.03 MONITOR
distribution tape.  This process is described in the INSTAL.DOC file  in
the   second   save   set   on   this   tape   and   in   the  Autopatch
Procedures/Reference Manual.  The MON703.CCL Distribution BACKUP Command
file found in the Installation Save Set may be used for this purpose.

A description of each edit is contained in the Edit Description file  in
Patch Set 014 (ANF703.D14).

The files required from Patch Set 014 to patch this product are:

PAT114.DPD
and all the Patch Files listed in section 4.0 for this product

You may use the ANF703.P14 Patch BACKUP Command file  to  restore  files
from  Patch  Set  014.   If  using  Autopatch for the first time on this
product you may use the ANF703.A14 Patch BACKUP Command file to  restore
files from all Patch Sets.
                                                                 Page 13


APL-10-V2               Product Information             PRODUCT CODE:
                          Patch Set 014                 APL1B2

This patch set does not provide any edits for APL-10-V2.

If you are patching the product for the first time, you  must  define  a
distribution  area and obtain some files from the APL-10-V2 distribution
tape.  This process is described in the INSTAL.DOC file  in  the  second
save  set on this tape and in the Autopatch Procedures/Reference Manual.
The  APL1B2.CCL  Distribution  BACKUP  Command   file   found   in   the
Installation  Save Set may be used for this purpose.  If using Autopatch
for the first time on this product you  may  use  the  APL1B2.A14  Patch
BACKUP Command file to restore files from all Patch Sets.
                                                                 Page 14


APLSF-10-V2             Product Information             PRODUCT CODE:
                          Patch Set 014                 APL1S2

This patch set does not provide any edits for APLSF-10-V2.

If you are patching the product for the first time, you  must  define  a
distribution   area   and   obtain   some  files  from  the  APLSF-10-V2
distribution tape.  This process is described in the INSTAL.DOC file  in
the   second   save   set   on   this   tape   and   in   the  Autopatch
Procedures/Reference Manual.  The APL1S2.CCL Distribution BACKUP Command
file  found  in  the Installation Save Set may be used for this purpose.
If using Autopatch for the first time on this product you  may  use  the
APL1S2.A14  Patch  BACKUP  Command  file to restore files from all Patch
Sets.
                                                                 Page 15


COBOL-10-V12C           Product Information             PRODUCT CODE:
                          Patch Set 014                 CBL12C

This patch set provides the required files to update  the  COBOL-10-V12C
compiler to edit level 1626, and LIBOL to edit level 1155.

If you are patching the product for the first time, you  must  define  a
distribution   area   and  obtain  some  files  from  the  COBOL-10-V12C
distribution tape.  This process is described in the INSTAL.DOC file  in
the   second   save   set   on   this   tape   and   in   the  Autopatch
Procedures/Reference Manual.  The CBL12C.CCL Distribution BACKUP Command
file found in the Installation Save Set may be used for this purpose.

A description of each edit is contained in the Edit Description file  in
Patch Set 014 (CBL12C.D14).

The files required from Patch Set 014 to patch this product are:

PAT114.DPD
and all the Patch Files listed in section 4.0 for this product

You may use the CBL12C.P14 Patch BACKUP Command file  to  restore  files
from Patch Set 014.

If you are using Autopatch for the first time on this  product  you  may
use  the  CBL12C.A14 Patch BACKUP Command file to restore files from all
Patch Sets.

This  product  may  be  Autopatched  via   EXE/REL   replacement.    The
CBR12C.CCL,  CBR12C.A14  and  CBR12C.P14  files  are  provided  for this
purpose.  See the INSTAL.DOC file for more details.
                                                                 Page 16


DBMS-10-V5A             Product Information             PRODUCT CODE:
                          Patch Set 014                 DBMV5A

This patch set does not provide any edits for DBMS-10-V5A.

If you are patching the product for the first time, you  must  define  a
distribution   area   and   obtain   some  files  from  the  DBMS-10-V5A
distribution tape.  This process is described in the INSTAL.DOC file  in
the   second   save   set   on   this   tape   and   in   the  Autopatch
Procedures/Reference Manual.  The DBMV5A.CCL Distribution BACKUP Command
file found in the Installation Save Set may be used for this purpose.

If you are using Autopatch for the first time on this  product  you  may
use  the  DBMV5A.A14 Patch BACKUP Command file to restore files from all
Patch Sets.
                                                                 Page 17


DECNET-10-V703          Product Information             PRODUCT CODE:
                          Patch Set 014                 DEC703

This patch set provides the required files  to  update  CTHNRT  to  edit
level  999,  FAL  to  edit  level  999,  and various MCOs to the monitor
modules.

If you are patching the product for the first time, you  must  define  a
distribution   area   and  obtain  some  files  from  the  DECNET-10  V4
distribution tape.  This process is described in the INSTAL.DOC file  in
the   second   save   set   on   this   tape   and   in   the  Autopatch
Procedures/Reference Manual.  The DEC703.CCL Distribution BACKUP Command
file found in the Installation Save Set may be used for this purpose.

A description of each edit is contained in the Edit Description file  in
Patch Set 014 (DEC703.D14).

The files required from Patch Set 014 to patch this product are:

PAT114.DPD
and all the Patch Files listed in section 4.0 for this product

You may use the DEC703.P14 Patch BACKUP Command file  to  restore  files
from  Patch  Set  014.   If  using  Autopatch for the first time on this
product you may use the DEC703.A14 Patch BACKUP Command file to  restore
files from all Patch Sets.
                                                                 Page 18


FORTRAN-10-V10          Product Information             PRODUCT CODE:
                          Patch Set 014                 FTN10

This patch set  provides  the  required  files  to  update  the  Fortran
compiler  to edit level 2573, the OTS to edit level 4251, and the DDT to
edit level 343.

If you are patching the product for the first time, you  must  define  a
distribution  area  and  obtain  some  files  from  the  FORTRAN-10  V10
distribution tape.  This process is described in the INSTAL.DOC file  in
the   second   save   set   on   this   tape   and   in   the  Autopatch
Procedures/Reference Manual.  The FTN10.CCL Distribution BACKUP  Command
file found in the Installation Save Set may be used for this purpose.

A description of each edit is contained in the Edit Description file  in
Patch Set 014 (FTN10.D14).

The files required from Patch Set 014 to patch this product are:

PAT114.DPD
and all the Patch Files listed in section 4.0 for this product

You may use the FTN10.P14 Patch BACKUP Command  file  to  restore  files
from Patch Set 014.

If you are using Autopatch for the first time on this  product  you  may
use  the  FTN10.A14  Patch BACKUP Command file to restore files from all
Patch Sets.

This  product  may  be  Autopatched  via   EXE/REL   replacement.    The
FTN10R.CCL,  FTN10R.A14  and  FTN10R.P14  files  are  provided  for this
purpose.  See the INSTAL.DOC file for more details.
                                                                 Page 19


IBMCOM-10-ET-V4         Product Information             PRODUCT CODE:
                          Patch Set 014                 IETV04

This patch set provides the required files  to  update  IBMSPL  to  edit
level 371.

If you are patching the product for the first time, you  must  define  a
distribution  area  and  obtain  some  files  from  the IBMCOM 10 E/T V1
distribution tape.  This process is described in the INSTAL.DOC file  in
the   second   save   set   on   this   tape   and   in   the  Autopatch
Procedures/Reference Manual.  The IETV01.CCL Distribution BACKUP Command
file found in the Installation Save Set may be used for this purpose.

A description of each edit is contained in the Edit Description file  in
Patch Set 014 (IETV01.D14).

The files required from Patch Set 014 to patch this product are:

PAT114.DPD
and all the Patch Files listed in section 4.0 for this product

You may use the IETV01.P14 Patch BACKUP Command file  to  restore  files
from Patch Set 014.

If you are using Autopatch for the first time on this  product  you  may
use  the  IETV01.A14 Patch BACKUP Command file to restore files from all
Patch Sets.
                                                                 Page 20


IBMCOM-10-HASP-V1       Product Information             PRODUCT CODE:
                          Patch Set 014                 IHSV01

This patch set provides the required files  to  update  IBMSPL  to  edit
level 371.

If you are patching the product for the first time, you  must  define  a
distribution  area  and  obtain  some  files  from the IBMCOM 10 HASP V4
distribution tape.  This process is described in the INSTAL.DOC file  in
the   second   save   set   on   this   tape   and   in   the  Autopatch
Procedures/Reference Manual.  The IHSV04.CCL Distribution BACKUP Command
file found in the Installation Save Set may be used for this purpose.

A description of each edit is contained in the Edit Description file  in
Patch Set 014 (IHSV04.D14).

The files required from Patch Set 014 to patch this product are:

PAT114.DPD
and all the Patch Files listed in section 4.0 for this product

You may use the IHSV04.P14 Patch BACKUP Command file  to  restore  files
from Patch Set 014.

If you are using Autopatch for the first time on this  product  you  may
use  the  IHSV04.A14 Patch BACKUP Command file to restore files from all
Patch Sets.
                                                                 Page 21


SORT-10-V4D             Product Information             PRODUCT CODE:
                          Patch Set 014                 SRTV4D

This patch set does not provide any edits for SORT-10-V4D.

If you are patching the product for the first time, you  must  define  a
distribution area and obtain some files from the SORT-10 V4D or COBOL-10
V12C distribution tape.  This process is  described  in  the  INSTAL.DOC
file  in  the  second  save  set  on  this  tape  and  in  the Autopatch
Procedures/Reference Manual.  The SRTV4D.CCL or CBL12C.CCL  Distribution
BACKUP  Command  file found in the Installation Save Set may be used for
this purpose.  If using Autopatch for the first time on this product you
may  use  the SRTV4D.A14 Patch BACKUP Command file to restore files from
all Patch Sets.
                                                                 Page 22


MONITOR-10-V703         Product Information             PRODUCT CODE:
                          Patch Set 014                 MON703

This patch set provides the required files to update the TOPS-10 monitor
to edit level 12807 (31007).

If you are patching the product for the first time, you  must  define  a
distribution  area  and obtain some files from the TOPS-10 V7.03 MONITOR
distribution tape.  This process is described in the INSTAL.DOC file  in
the   second   save   set   on   this   tape   and   in   the  Autopatch
Procedures/Reference Manual.  The MON703.CCL and CSP703.CCL Distribution
BACKUP  Command files found in the Installation Save Set may be used for
this purpose.

A description of each edit is contained in the Edit Description file  in
Patch Set 014 (MON703.D14).

The files required from Patch Set 014 to patch this product are:

PAT114.DPD
and all the Patch Files listed in section 4.0 for this product

You may use the MON703.P14 Patch BACKUP Command file  to  restore  files
from Patch Set 014.

If you are using Autopatch for the first time on this  product  you  may
use  the  MON703.A14 Patch BACKUP Command file to restore files from all
Patch Sets.
                                                                 Page 23


MPE-10-V703             Product Information             PRODUCT CODE:
                          Patch Set 014                 MPE703

This patch set provides the required files to update MPE-10-V703 to edit
level 999.

If you are patching the product for the first time, you  must  define  a
distribution  area  and  obtain  some  files  from the TOPS-10 MPE V7.03
distribution tape.  This process is described in the INSTAL.DOC file  in
the   second   save   set   on   this   tape   and   in   the  Autopatch
Procedures/Reference Manual.  The MPE703.CCL Distribution BACKUP Command
file found in the Installation Save Set may be used for this purpose.

A description of each edit is contained in the Edit Description file  in
Patch Set 014 (MON703.D14).

The files required from Patch Set 014 to patch this product are:

PAT114.DPD
and all the Patch Files listed in section 4.0 for this product

You may use the MPE703.P14 Patch BACKUP Command file  to  restore  files
from  Patch  Set  014.   If  using  Autopatch for the first time on this
product you may use the MPE703.A14 Patch BACKUP Command file to  restore
files from all Patch Sets.
                                                                 Page 24


UTILITIES-10-V703       Product Information             PRODUCT CODE:
                          Patch Set 014                 UTL703

This patch set provides the required files  to  update  ACTDAE  to  edit
level  143,  BACKUP  to edit level 617, BOOT to edit level 50, COMPIL to
edit level 600, CRSCPY to edit level 52, DAEMON to edit level 1014,  DDT
to  edit  level 643, FILCOM to edit level 115, INITIA to edit level 255,
LOGIN to edit level 2056, LOGOUT to edit  level  2113,  NEWACT  to  edit
level  10, SCDEXE to edit level 22, SYSDPY to edit level 635, and SYSTAT
to edit level 341.

If you are patching the product for the first time, you  must  define  a
distribution  area  and  obtain  some  files  from the TOPS-10 7.03 CUSP
distribution tape.  This process is described in the INSTAL.DOC file  in
the   second   save   set   on   this   tape   and   in   the  Autopatch
Procedures/Reference Manual.  The CSP703.CCL Distribution BACKUP Command
file found in the Installation Save Set may be used for this purpose.

A description of each edit is contained in the Edit Description file  in
Patch Set 014 (UTL703.D14).

The files required from Patch Set 014 to patch this product are:

PAT114.DPD
and all the Patch Files listed in section 4.0 for this product

You may use the UTL703.P14 Patch BACKUP Command file  to  restore  files
from Patch Set 014.

If you are using Autopatch for the first time on this  product  you  may
use  the  UTL703.A14 Patch BACKUP Command file to restore files from all
Patch Sets.