Google
 

Trailing-Edge - PDP-10 Archives - SRI_NIC_PERM_SRC_1_19910112 - 6-documentation/format.doc
There are 12 other files named format.doc in the archive. Click here to see a list.


FORMAT.DOC -- Changes from V4(0) to V5(0)
October 1981






























COPYRIGHT (C) 1977,1979,1982 BY
DIGITAL EQUIPMENT CORPORATION, MAYNARD, MASS.


THIS SOFTWARE IS FURNISHED UNDER A LICENSE AND MAY BE USED AND  COPIED
ONLY  IN  ACCORDANCE  WITH  THE  TERMS  OF  SUCH  LICENSE AND WITH THE
INCLUSION OF THE ABOVE COPYRIGHT NOTICE.  THIS SOFTWARE OR  ANY  OTHER
COPIES  THEREOF MAY NOT BE PROVIDED OR OTHERWISE MADE AVAILABLE TO ANY
OTHER PERSON.  NO TITLE TO AND OWNERSHIP OF  THE  SOFTWARE  IS  HEREBY
TRANSFERRED.

THE INFORMATION IN THIS SOFTWARE IS SUBJECT TO CHANGE  WITHOUT  NOTICE
AND  SHOULD  NOT  BE  CONSTRUED  AS  A COMMITMENT BY DIGITAL EQUIPMENT
CORPORATION.

DIGITAL ASSUMES NO RESPONSIBILITY FOR THE USE OR  RELIABILITY  OF  ITS
SOFTWARE ON EQUIPMENT WHICH IS NOT SUPPLIED BY DIGITAL.
FMT5.DOC                                                        Page 2


FORMAT.DOC -- Changes from V4(0) to V5(0)
October 1981



1.0  SUMMARY

FORMAT provides the mechanism for formatting  and/or  verifying  RP04,
RP05  or  RP06  disk  packs  that  are  configured  to RH20's.  FORMAT
produces a pack in the identical format to one that was created  using
the  diagnostic,  "DDRPI".  FORMAT runs during timesharing only, while
"DDRPI" can FORMAT in STAND-ALONE mode only.

FORMAT Version 5(0) runs on TOPS20 Release 5.

FORMAT is documented in the TOPS-20 Operators Guide.



2.0  EXTERNAL CHANGES

There are no external changes for Release 5.



3.0  KNOWN BUGS AND DEFICIENCIES

FORMAT can not be run under batch.  Multiple copies of FORMAT can  not
be run.  WHEEL or Operator PRIV are required to run FORMAT.



4.0  Installation and Build Instructions


4.1  Files Needed to Run FORMAT

FORMAT consists of one file, FORMAT.EXE


4.2  Instructions for Loading and Installing FORMAT

Mount the tape  labled  Installation  Tape  on  MTA0:   and  type  the
following commands:

     SKIP MTA0:5 FILES
     R DUMPER
     TAPE MTA0:
     REWIND
     DENSITY 1600-BPI
     SKIP 1
     RESTORE <*>FORMAT.EXE (TO) <SUBSYS>*.*.-1
     REWIND
FMT5.DOC                                                        Page 3


4.3  Files Needed to Build FORMAT

FORMAT is built from the following file:

     FORMAT.MAC

In addition, the following file must be on SYS:

     MONSYM.UNV


4.4  Instructions for Building FORMAT

Mount the tape  labled  Distribution  Tape  on  MTA0:   and  type  the
following commands:

     R DUMPER
     TAPE MTA0:
     REWIND
     DENSITY 1600-BPI
     SKIP 1
     RESTORE <*>*.*.* (TO) <self>*.*.*
     REWIND
     ^C
     SUBMIT FORMAT.CTL/TIME/UNIQ:0/RES


4.5  Special Considerations

None.



5.0  INTERNAL CHANGES

REFER to FORMAT.TCO for detailed inFORMATION about changes.



6.0  SUGGESTIONS

FORMAT is a privileged program that makes  use  of  TOPS20  diagnostic
interface,  DIAG.  One should exercise extreme caution if modifying or
patching FORMAT.


[End of FMT5.DOC]